Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Is there a way to use Cisco Prime Infrastructure to convert an LWAPP(s) to autonomous mode? I need to convert 30 APs back to autonomous mode before we sell a site.
Is there a way to display a login banner on the AP CLI? I've tested hoping that the login banner from the WLC would trickle down to the APs, but no dice. Are all login attempts to the AP's CLI logged anywhere? I did not notice anything relevant fro...
We are currently deploying MR33 into our remote sites , we currently use a fixed Wireless LAN controller at the data centre and tunnel guest SSID clients across MPLS to local Internet breakout via our firewall , our remote site do not have direct int...
Hello,We are using Prime Infraestructure 3.5.In the inventory we have a Switch (Cisco Catalyst 2960-24PC-S), that shown "Switch Port Trace" in the inventory status. Anyone knows whats it mean?"Collection Status: Device is added in Switch Path Trace ...
Good evening! I'm having this odd problem at my company. We have about 4 AP connected to the same network here.local and our employees connect to those for their various tasks. But for some reason most of our employee's iPhones can only first connect...
Hello I have a problem my problem is thats my AIR-CAP2602I-E-K9 is losing many packets.. The users complainants that the network is running slow, and when im doing a speed test on thats AP the result is 14/50. Way way to slow in releative to others ...
Hi, I setup a cpu ACL for specific IPs and everything works fine. However, I can see counters go up but there are no logs being generated. I tried looking at "debug packet logging" but I never got a log showing which IP address was being denied.
Hello i have all acces point are same channel 36 with 5 gh band i would to know if correcte , it ok for this all access point are same channel ? can give a problem or not ?, please , i would some one answer me for this problem !! and i would w...
We have purchased new WLC 5520 and some access points we have configured Service Port, management port, and AP management port of WLC, but when we are trying to join APs to WLC we are receiving below errors. [*03/04/2019 05:19:01.0166] CAPWAP State:...
Hello, I have no experience with Cisco wireless products and I have a single Cisco AIR-AP1850 and want to configured as standalone but this message didn't allows me to do anything (CAPWAP State: Discovery).Someone suggested that I need to upgrade th...
Good morning. I have issues with Samsung Galaxy Xcover 2 and 3 phones that connects to our customers Wifi network. They have WLC5508 with SW 8.1.131.0 and use CAP2702 in local mode. The SSID is set up with WPA2, PSK. The Samsung clients connect, but ...
I'm running ME8.8.111.0 in a small setup with 3 APs and was wondering why DCA with channel-width "best" sticks with 20MHz channels. I tried to set them to 40MHz instead of "best": >config advanced 802.11a channel dca chan-width 40ERROR: Configured ...
Hello Team, Users are facing Skype dropping issue only other application are working properly plz help how to troubleshooting
I have a 2504 with software v 8.0 , yes I will upgrade to 8.5. 2 questions1. is there a way view bandwidth on this device, I cannot find any reports2. is the dashboard customize able , I read that 8.1 could add widgets and I do not see that in 8.0
Hi Community,Is it possible to SSH/Telnet to an Access Point (AP) via the Cisco Wireless LAN Controller (WLC) CLI? I have performed a '?' at the '>' EXEC prompt and cannot see any valid options. Regards,Nathan.
