Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Bonjour la communauté, Mon problème est le suivant :Je recherche désespérément un mode d'emploi sur la configuration de six bornes Cisco. Les six auront le même SSID. En sachant qu'un serveur DHCP existe déjà. Et que lorsque je n'active pas la foncti...
Setup: 2x WLC5520 (version 8.2) in SSO HA Question: If a SSO HA pair connects to two switches, will these two switches need to be VSS or Stacked? What I read from Cisco documentation is that switches must be in VSS/Stack. Could anyone please confirm?...
Resolved! Access points not showing in Prime 3.1
I have access points that I prepped at my office. They are 2802i. I am replacing 3602 access points and using 7500 flex controllers with 8.2.130.0 software. When I replace them at buildings, they do not show up in Prime. The old ones are still the...
Hi, I have a strange issue on a wlan which configured for Flexconnect local switching whereby, if I have two clients connected to the same AP they are able to ping each other. However, if one client then roams to another AP the communication stops ...
Hi, I have a quick question. We have Flexconnect Local Switching with no VLAN mapping on the APs or Flexconnect Group. If APs lose connection to WLC, would the clients get disconnected or stay connected? The site has no VLANs and it's running on Nati...
We have a device portal set up for students to register certain endpoints such as PS4s and XBoxes. At the end of each semester we want to clear out all devices that are registered in the device portal. What is the best way to do that? Is it throug...
I've got 1200+ APs (2802i) across several sites, connected to a 5520 WLC. I need to find a way to monitor these APs and generate text alerts when either the AP goes down, or the radio interfaces go down. What's the best tool to do that? In addition t...
Hi, I am facing problem with 1852 AP with 2504 WLC. It disconnected the clients automatically. Please find the attachment log report for that clients. Please advise me the solution. Thanking You- Azizur Rahman
Hi, we have purchased 5 AP license and want to add in WLC 2504. But when we install license from tftp server it's give an error. It is showing "Installation process complete 1 License(s) failed; " Kindly help me to add license in WLC 2504. Regards ...
I need to turn an AP 2800 series into autonomous mode, because I don't have a cisco controller to manage it
Hi we want to extend for a customer the corporate network to another building just on the opposit side of the road (50 meters distance). We are thiking about installing 2 1562i APs as Point to Point Bridge. Both APs can me mounted on the roof and h...
hi Guys, I'm going to install 20 1832i AP and Cisco virtual wireless controller. I Know there apre some voice problem in this kind AP where voice packet are stopper. do you Know somethink about?
setting up a 5520 controller it came with version 8.1.102 do i need to load FUS 1.9 (firmware upgrade) before upgrading software to 8.3?
Dears, I have a requirment to have access controll list in WLAN controller. we want to give limited access to Level-1 team. the access should be limited to adding and deleting MAC address authentication. I tried searching but didn't find any thing...
Hello, Our company used to have a bunch of 2702 access points configured as autonomous with no problems. We eventually configured some WS-C3850-48P switches as wireless LAN controllers. Since that time, we've run into issues. A typical user has a ...
