Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
From the MSE wips-cli (/opt/mse/wips/bin/wips_cli) when i do wIPS>show alarm list Key Type Src MAC First Time LastTime Active TimeZone IsServerAlarm ChannelBandWidth ---------------------------------------------------------------------...
Ethernet fallback setting is radio wave no stop? :WLC 5520 8.5.131 WLC 5520 use version is 8.5.131 [Wireless] > [Access Points] > [Global Configuration] [FlexConnect Ethernet Fallback] > [Radio Interface Shutdown] checkbox on [FlexConnect A...
Hi, I've been looking and looking for an answer but I just can't seem to find it. In Aironet AP's with external antennas like the 1562E which I have to survey with have the option to use 2 dual band antennas on the bottom of the AP or use single ...
i just bought a WLC 3504 device, after completion at the process setup wizard. then i can't enter the web based controller stage, with ip management that i have set. how can i enter this section.? for the switch i have set it to trunk mode
hi referring to the configuration i have problem with my wifi (employee wifi) as appear on pic the WiFi on some laptop is not able to connect and some is able to connect ? dont know why ? maybe the configuration need to be changed with some settin...
Hi Everyone Anyone know how to schedule reboots on a AIR-AP1041N-A-K9 or if it can be done at all? I have a wack of them that I need to update firmware on and would like to bounce them on a staggered schedule rather than immediately after the firmwar...
Hi all. I am just coming into the IT director after the previous left the company. I am looking through everything, especially the licenses. If I select one of the APs, I see that the majority say 3 or 4 years on the term. When I look up top though, ...
Upgrading code on an HA pair that I have done many times I ended up in maintenance mode. As you can see from the attached file, it the new image was not transferred to the secondary. I can get to the secondary via the redundancy management IP given c...
Hellodo you know any summarized document, or tools to compare different version of Cisco AIR-AP2802I-E-K9 access point , particularly comparing from 8.2.16 to 8.3.122?and/or a document that confirm if various software versions affect which parameters...
I have all of my SSID's controlled by an central SSID template. Can I disable a specific SSID for a specific Network by using the "Access Control" functionality? Will that disable the SSID for all of the Networks that are using the template or just t...
Can we upload a Self Signed Third Party Certificate to Cisco WLC? We are already using same certificate at a WLC of HP Procurve and now we want to upload the same to Cisco WLC. Currently we are using auto generated certificate by Cisco WLC.
I have Cisco Wireless Controller 5520 - 8.3.132.0 - With Cisco Prime 3.5.0 I have about 900 AP - and a daily count of 5000 Client give or takeThis is running smoothly whit no problems - My Question is. I have made a setup with 3 AP2802 - for an exami...
Hello, I have a strange problem that I still have not found a solution for. I have a vWLC with 3 Cisco 1142n ap's connected to it. Every once and a while when a client roams, the speed of the client drops to around .30 to .50 mbps up and down. The ...
I've a setup where the customer is using 1905 router for Internet access. They have a LAN segment with 192.168.1.0/24 and an WAN segment of 150.129.126.168/29 provided by ISP. Right now they are using a D-Link router for internet access and its worki...
I manually disabled a client in the monitor>clients and when I check in the WLC's CLI the client is excluded. Now I can't find a way to enable the client using either CLI or GUI.
