Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
AP1131 only support highest 54Mbps speed rate , from my test , AP can only go to 20Mbps speed on one direction , merge channel bandwidth may be the way to use all raise the speed rate. i only know Aruba and huawei can do this at least,with AC mode...
Hey there. We are deploying a new wifi network to one of our locations and running in to a weird problem. When we set the 802.11a radio to 40MHz (or even 80MHz) the settings don't apply to the AP. The WLC says the settings have been applied, but when...
Hi, I'm troubleshooting an external antenna issue on mesh network with 1572 APs. I have a very low SNR while taking the output of a "show mesh ap tree" or "show mesh neigh summary <AP Name>". But when I issue a "show mesh neigh detail <AP Name>" I ha...
Hi, I jhave a wlc 2504. I am trying to configure through the gui configurator: i Save the configuration but When i try to Connect with the new IP i cannot: i have tryed to use cli configuraton but i cannot log in with the new ip...seem that not Save ...
Hi, How can i view the serial number in Prime infrastructure as well as firesight management center and both are VM only. Thanks Muthukumar
Resolved! WLC Replacement in WCS
Hi, We have a client running 5 x 4404 WLC's managed via WCS V7.0.240.0. I know it's no longer supported and this system is due to be replaced in the next 6-8 months but we have a controller down and I need to replace it ASAP (I already have the hard...
Hi, I have a WLC 2504 running in 8.2.151.0 with 1852 APs I have configured a SSID with 801.X through a NPS. The NPS assign different VLAN depending on some criteria (3 different VLAN) This works fine when I use central switching. I now want to have ...
Hi, I want to know how to configure one active WLC and two HA (SSO) controllers. This is required as following : - If the active WLC goes down, APs will join to the first HA WLC. - If the first HA WLC goes down - while the active WLC remains down-...
Hi all, I have configured a 5508 controller to connect local and Flexconnect APs. There is an additional 2504 for termination of a guest Internet access SSID. On the 5508 and 2504 I have configured SSID "guest1" and anchoring. This is working as expe...
お世話になります 現在 コントローラーCT7510のもと、無線アクセスポイントは AIR-CAP1702I-Q-K9と AIR-CAP1702I-Q-K9を 接続しております。 MSEでヒートマップを管理しつつ CMXを導入し ユーザーデバイスの動線管理を 実施したいですが HWの前提条件として 1602と1702はCMXに対応しておりますでしょうか？
Is there a way of changing the default settings for both Prime heatmaps and Planning mode? I'd like the A radios and something higher than -75 to be the default on opening a map. this on either a user-by-user preference, or even a global default for...
Hi Does anyone have high resolution pictures of (or can link me to the exact cisco picture): Power cord ends for South Korea (meraki) - MA-PWR-CORD-EU and Power cord ends for Japan (meraki) - MA-PWR-CORD-US We have had some problems recently ensuring...
Hey guysWe upgraded the WLC 8500 from 8.0.110.9 to 8.4.100.0 & after upgradation most of the flexconnect mode access point(AIR-CAP3602I-N-K9) unable to join the WLC.but local mode access point successfully joinedCan anyone suggest why access point un...
Hello I have an AP with two SSIDs each in a different VLAN and I want to filter the associations to one of the SSIDs by the clients mac, I have seen many solutions on the WEB but I have not achieved what I want, the only one I could Is to filter all ...
Hello, I bought PAK License with following article number, L-LIC-CTVM, I tried to generate License file through PAK number, everything going well till the last step where the product ID filed is not active (please see attachment), upon giving the ser...
