Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi Guys, I have WLC 5508 with this software ver. 8.0.140.0. and I enabled out of the box and Enable Persistence in RF profile. The issue is when I installed a new AP will go to out of the box and Radios is down...it's normal until now! when I moved t...
Hey all! I have a Cisco WLC 2500 with several APs connected and several SSIDs. When a malicious person sets up a rogue AP with the same SSID as ours, I would like to be informed. Where can I configure that an alert is sent out (maybe a syslog serv...
I have been working on this issue for several weeks. Now I have found the issue in Prime when I logged the client. But I am not sure how to solve the problem. The PC never moves from the desk... so I don't know why there was a Controller change, loss...
Does the 2566-P4W-R come with a mounting bracket as depicted in the attached image? I can't seem to find what all comes with the antenna or if Cisco makes a mount kit for it.
Hi, Could someone tell me if its is possible to have the following configuration please? -Single wlan broadcast across 2 sites (A and B), configured for local switching but also mapped to a dynamic interface on the wlc. -Site A uses local mode APs ...
I have recently deployed 3800 series access points in a flex connect environment and notice I am having issues with maintaining connectivity to the wireless network on the CP-8821 phone. When roaming between access points I drop the signal completely...
I've got a virtual WLC with numerous remote aps connected to it. I'm trying to connect one locally but its not joining ive had this problem before and somehow got one to join locally but want to get to the bottonm of this, see below for the ap start...
Resolved! cisco 3802i change regulatory domain
Good day. Found that there is a possability to change regulatory domain in a few cisco aironet models http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ux-ap/guide/uxap-mobapp-g.html http://www.cisco.com/c/en/us/td/docs/wireless/controller/...
I've seen this error come through a lot from few days Status Code 3: "The username specified cannot be used at this time. Perhaps the username is already logged into the system?" There were no changes made on the config side. We create new guest wifi...
Is it possible to run a discovery in Prime Infrastructure 3.1 without adding the devices to Prime? I need to create the budget for a project that will add our switches to Prime but I don't know how many we currently have and the models. So basically ...
Hello everyone,We've recently bought 30 AIR-CAP1602I-A-K9 APs and 2 AIR-AP2802I-A-K9 APs to use as redundant controllers. When we deployed the network we've realized that many APs remained at the "Not Joined" status and if I check the configuration ...
Dear Gentleman, according to http://www.cisco.com/c/en/us/products/wireless/wireless-lan-controller/product-comparison.html it is stated that there is a Bandwidth Limitation for Mobility Express to 1Gbit/s. For example, imagine one installs Aironet 3...
Hello, can anyone help me with this problem. I need an oid to view the number of connected clients per Access-Point. I already tried the SNMPv2-SMI.mib but i have no results with it. Hope some of you can help me. Thanks.
Hi, I've assumed responsibility for a network, and they have deployed AIR-CAP1602E-A-K9 AP's at remote locations. They're hooked into injectors, which of course are fed from a switch. I need to buy another one, but I'm confused in that I'm reading on...
Hi,I am wondering if I can set ctcp for a specific for IPSEC peer on cisco ios router.Currently I have 3 ipsec tunnel running normally over ESP, however there is another tunnel that I am trying to setup but it is failing but I am suspecting ISP is fi...
