Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I have a hunch that people have run into this sort of thing before. (TAC case open, but curious if somebody here just knows the answer) APs at our Home Office are in Local ModeAPs at our Remote Offices are in Flex Mode When clients roam from a remo...
Hello,I have a Cisco 891 ISR that's working fine with several clients on a local network both wired and wireless.Just picked up a wireless printer and I can see and ping the printer from the router, but the PC setup can't find the printer and thus wo...
Can we use multiple ports on Cisco 2504 controller for multiple Virtual LAN , I have created a different Virtual LAN but I want to get it routed from different port on Cisco 2504 port not from the common port we use.
Hi all,I'm trying to poll the WLCs at our sites via SNMP to get data rates.I found what I believe are the right OIDs in the CISCO-LWAPP-WLAN-MIB but all of my controllers are returning a value of 0 which, per the MIB, means that setting is disabled. ...
Hi All, My office is using the Old Cisco Aironet 1130 Series and planing to replace . what is the best replacement that i can have for this. The Site has around 90 Users sharing 8 AP and WLC is deployed in the Site ( WLC 4400 series-- do i need...
Hi All, I would like to ask. What do you think is it possible to run AIR-CAP2602E-A-K9 without antenas? Reason is we have this ap without antenas and clients can not connect but wlc show everything ok
Hello I'm looking for the procedure to follow when changing the management interface on a WLC 5500 with respect to the actions I need to take in Prime 3.2? Thanks in advance.
Hi, I am trying to create a wireless mesh between my house & my garage. The good news is the MAP (Garage AP), can see the RAP (Basement AP) & I have devices connecting wirelessly in the garage. The new issue is I have some wired devices that I wo...
I have 2504 WLC which configured High availability. i was trying to upload IOS image from TFTP server , now more than 10 hours over still its in progress. 1. If i try with " RESET SYSTEM FORCED" existing configuration will erase from WLC ? 2. And...
Dear All, we are planning to disable the data rates 6 + 9 Mbit/s for the 5 GHz band (disabled instead of supported) as we have already done for the 2.4 GHz band. Prior to doing this however, we'd like to see how extensively the data rates 6 and 9 Mbi...
Hi, I have an 1852i AP and my etherswitch module powers it at 15.4 W and when I use the power injector it does the same. When I use the original power supply it is full powered. I have raised the wattage on the etherswitch module but it does not make...
I just bought a 2504 WLC off of eBay, and of course it would appear to be dead on arrival. Well, at least partially. When I power it up, all I get is the following: WLCNG Boot Loader Version 1.0.20 (Built on Jan 9 2014 at 19:02:44 by cisco) Board ...
I am in need of assistance figuring out the right support to purchase for my APs (AIR-AP2802I-A-K9C). The APs originally ran mobility express image. Now, we are planning a migration to a controller based system using the Cisco 3504 WLC (AIR-CT3504-K9...
Hi I'm install in my network one new AP 1562b, but due IOS of the controller I dont can install in controller, I gonna configuration it how autonomos (Mobility Express) but in documentation talk that Mobility can't work with other Controller. "Yo...
Hi All, Thanks in advance for any responses. I understand that broadcast traffic is not passed by the WLC(by default) but in our situation we have centralized WLC's. We keep the WLC's in data centers and have hundreds of sites that have AP's in loc...
