Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi,   I ran out of idea with this problem I have, I used to able to snmpwalk the full MIB tree on my Cisco 2500 wireless controller but I no longer can after a reboot on it WLC.  I believe all the configs are fine, no error on snmp neither.  I am abl...

buttercuff by • Community Member
  • 6181 Views
  • 4 replies
  • 0 Helpful votes

Hi When we make a change and save the configuration to flash on 5508, one box window appears, which says Are you sure you want to save configuration to flash so that on a reboot the controller retains the configuration? do you think the controller wi...

wfqk by • Level 7
  • 13667 Views
  • 4 replies
  • 0 Helpful votes

I have configured wccp in my core switch, 4500x. My proxy is a McAfee Web Gateway. The wccp configuration is pretty straightforward, and is working for my wired and VPN users. It is not working for my wireless users. I have enabled wccp in the wirele...

ergamusai by • Level 3
  • 1191 Views
  • 2 replies
  • 0 Helpful votes

Hi Everyone   I am new to configuration, I want to learn how to configure wireless controller with access point or any models of controllers and access points. I have tried with the help of configuration guide but that was not mentioned about the con...

narayana by • Frequent Visitor
  • 1542 Views
  • 2 replies
  • 0 Helpful votes

Hello,   We will soon upgrade to WLC from 7.4.110 to 7.6.120 and find out a new feature : spleeping client. I was wondering the purpose of the sleeping client vs idle timeout/session timeout.   In our case we have an idle client set to 14400 seconds ...

Hello all,   I'm dealing with bug CSCvd86274...   Symptom:"show cdp neighbor" at the Switch side shows the AP Platform as "Unknown" instead of AIR-APXXXXX-K9 The workaround says to : 2) Break the boot process, go to u-boot>> and do the following:u-bo...

shamg1974 by • Level 3
  • 1065 Views
  • 1 replies
  • 0 Helpful votes

Hello, I've been reading up on Real Time Location Services and found a lot of good discussions on the topic.  I have one question that I haven't been able to answer.  Will the 3504 WLC support RTLS?  I haven't found anything that says no, but then I ...

Shawn McCoy by • Community Member
  • 1084 Views
  • 1 replies
  • 0 Helpful votes

Hi all,  I have that problem, that the AP does not join to WLC after the priming process.  I get the following error logs:  *Mar 3 20:40:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.31.31.155 peer_port: 5246 *Mar 3 20:40:2...

Hi AP1130 is taken out of WLC. when console is connected to it, it requires password. the password is not default password. and i do not want to password recovery. What password it could be? In WLC, we only has password for users to access wifi. i do...

wfqk by • Level 7
  • 2769 Views
  • 4 replies
  • 0 Helpful votes

Hi all,   We're currently migrating a Juniper based wireless network to Cisco wireless. We're using one SSID with EAP-TLS to connect some Windows Mobile and Windows CE devices. Lately we have found a problem that our Windows CE devices can't connect ...

PatrickOS by • Level 1
  • 4968 Views
  • 8 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card