Does anyone know if the 1815T Officeextend AP is compatible with vWlC 8.5.103.0? according to the documentation I have seen it should be but I am seeing the AP pull an IP address and partially join before continuously repeating the process over and ...
Hi, The IT service installed two new Wi-Fi routers within our company (Cisco Aironet 1830). They completely set it up and I should now manage it. However, we are having difficulties with some iPhones that simply can't connect to the network. iPhon...
Hello ExpertsWLAN Controller 4400 series connected to Catalyst 4506 on vlan 12. Access switches got managment vlan 5 and vlan 1 shutdown.what config is needed on ports were Access points are connected. Access switch is in vtp client mode.cheersSamuel
is it the correct practise to set the wlc and the ap in the same vlan? in my previous implementations i noticed that when i set the ap and the wlc in the same vlan they wont see each other? i usually separate the ap in a different vlan and set the dh...
I have a situation with Cisco WLC 4402. I have 2 WLAN networks. Corporate network is in vlan188 and guest network is in vlan192. Management interface is on untagged vlan. I would want the controller to be accessible via corporate network but not the ...
Hi Folks, Latest project is to migrate 160 APs from existing 5508s running as primary and secondary. The existing code is version 8.0.x. Client want to install a pair of new 5520s configured in high availability mode, not just primary and secondary...
Hi We currently have a guest network setup with internal Foreign Controller tunneling guest traffic into DMZ to Anchor Controller, is it possible to set up another guest SSID and use another Anchor controller but still tunnel Guest traffic for new SS...
Hi All Today you have high density access points, what defines them as high density? We have Meraki MR42 / MR52 etc, there is a hard limit of 120 clients on 1 access point, how many clients do they recommend today before the quality starts to degrad...
Hi, 1600 series AP's in autonomous mode. I have 2 SSID's: 'corp' and 'guest' both in separate vlan's with 802.1q sub-interfaces. Corp uses radius and guest uses a PSK, and access is restricted to internet only from the guest. this set up works fi...
i have ( 4404 wireless lan controller) and i lost my data about the management ip and vlan. i want to reset the controller to default factory, unfortunately i don't have a console cable to log into the controller and reset it. can i hard reset it in ...
We have 200+ Meraki MR32 APs installed over 8 locations.On one location (10 APs), we use classrooms during the day. In the evening, the classrooms are used by another organisation, with their own wifi APs. We each have our own SSIDs.To prevent our AP...
Hi, I have Cisco WLAN Setup with following details WLC: 7.4.130.0 WCS: 7.0.172.0 MSE: 7.0.105.0 Context Aware Service : 7.0.105.0 wIPS Service: 1.0.2066.0 The issue is that i am not able to track rogue access points via WCS. The snapshot of WCS is ...
Dear all, I am performing an estimate on CCW. I have to configure a Wireless controller with 12 AP licences based on the Cisco one model. Please see below the BoM : C1-AIR-CT5508-K9 Cisco ONE - 5500 series WLAN Controller w/ 0 AP lics CON-SNT-CT5508K...
Am I reading the documents correctly that these currently cannot bridge to each other either in Mobility Express mode or connected to a WLC?
Dears,We want to do bandwidth limitation on a specific WLAN on 2500 WLC. what is the steps to do that ?Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-14-2026 08:08 AM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 3 | |
| 2 | |
| 2 |
