Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, I'm new to the world of Cisco and routing and am trying to set up a 1841 as a 3G device. I have a working sim card but my cellular interface is flapping.. I think it has something to do with the cell profile but could use some help, thanks. Belo...
Resolved! Upgradation in 2504 WLC
Hi Experts, We are having 2504 WLC with 7.4.121.0 code and FUS code of 1.0.0 . We would like to upgrade the code to 8.0.120.0 , and in recommedations i have seen that we need to upgrade the FUS code to 1.9( 1.0.20) . Can I upgrade the FUS code dire...
Hi, I need to configure the 5500 series wireless controller please give the best practiced advice (configuration of vlan,ssid ,about DHCP option etc ).and also switch configuration
Hello, I'm having a problem with the bounjor protocol in a LAN but only from the wireless AP(AIR-SAP702i). On the wired network, everything is ok. I've enabled IGMP snooping but no lock.The router i'm using is a 889G-LTE.There is only one VLAN. Any ...
My client has recently moved one of their branch offices from the WAN to a site 2 site VPN setup between an ASA5525 and ASA5506. All traffic from the branch office goes over the VPN tunnel. After the move to the VPN the APs keep flapping with the fo...
Hi, does licenses of Prime Infrastructure 2.x will work on a Prime Infrastructure1.3? Regards, Thomas
My question is related to BYOD and Employee Personal Devices on-boarding. I am trying to implement ISE CA service for authentication of employee devices without using AD. Is PEAP-MSCHAPv2 compatible with Internal ISE user database? I really want to ...
Hi Friends, I'm really poor in WLC deployment. I need to deploy a new 5508 WLC into network as a secondary controller. The primary WLC (5508) has been configured as a single WLC as of now and working good.... Now I need to deploy the new 5508 as the ...
Hi all, We have a large number of 2702i's and 3602e's running lightweight code level 8.0.110.0 and connecting to a AIR-CAP2504-CT-K9 throughout all of our branches. Occasionally, one or two of them will drop their static address, and try to use a DH...
We are running CUCM 9.1.2 with about 560 - 7925G phones running 1.4.4.3. We have a new Network Profile we'd like to roll out. When we place WLANDefault.xml on the tftp servers, and restart tftp service on each of them, we reboot a phone. The phone i...
OK, I have enrolled about 50 iPhones through the BYOD portal. One of them gives me the attached error: The system administrator has either not configured or not enabled a policy for your device. Contact the help desk for assistance. I tired deleti...
hello there, can you help me where i can configure the wap321 AP to forward data just at port 8004.what i want to do is that a mobile device can access an http application through port 8004 , it mustn got anywhere else.i dont want to have the device ...
Trying to find out which one does what with regards to MSE and Prime, can the raw data be used from either or are their specific things that one does that the other doesn't?
Resolved! Resetting a 2504 wireless controller
Outside of the GUI, how do you reset a 2504 wireless controller back to factory settings. Thanks
We have a working wireless setup using Aironet 1142 connected to Windows Network Policy Server using PEAP. Other clients can connect to the wireless fine but the 7925G phone just will not connect using PEAP. The only way we have been able to get it t...
