Can somebody help with given below error? I have already upgraded my access point with new firmware. deauthed from BSSID reason 3: STA is leaving IBSS or ESS
Can somebody help with given below error? I have already upgraded my access point with new firmware. deauthed from BSSID reason 3: STA is leaving IBSS or ESS
I run a large WPA2 Enterprise secured wifi environemnt with a radius authentication back-end. After yesterday's Windows 10 November update, we're seeing increased reports of inability to connect to these SSIDs. Is anyone else seeing this type of use...
Hello all I recently bought an access point Aironet 702i (700 series) but when I start the device. I got a green / amber / red blinking without stop. I tried to reset the device by : • holding the mode button • unplug / re-plug the device • wait for ...
Dear All, I am have problem in subject issue. The Authentication with Active Directroy was workin fine and all of a sudden it has stopped. Now its not authenticating new users to Cisco WLC 2504 through Active Directory Windows Server 2008r2 Standard....
Dear All, I am have problem in subject issue. The Authentication with Active Directroy was workin fine and all of a sudden it has stopped. Now its not authenticating new users to Cisco WLC 2504 through Active Directory Windows Server 2008r2 Standard....
Hi, On a IR829, I have two sim slots. I'm trying to enbale both sim at the same time in order to have two networks, which then will be associated each to a dedicated vlan. Is it possible ? I've seen something about multple PDN and multihoming on the ...
Hi, I'm new to the world of Cisco and routing and am trying to set up a 1841 as a 3G device. I have a working sim card but my cellular interface is flapping.. I think it has something to do with the cell profile but could use some help, thanks. Below...
Hi Experts, We are having 2504 WLC with 7.4.121.0 code and FUS code of 1.0.0 . We would like to upgrade the code to 8.0.120.0 , and in recommedations i have seen that we need to upgrade the FUS code to 1.9( 1.0.20) . Can I upgrade the FUS code direct...
Hi, I need to configure the 5500 series wireless controller please give the best practiced advice (configuration of vlan,ssid ,about DHCP option etc ).and also switch configuration
Hello, I'm having a problem with the bounjor protocol in a LAN but only from the wireless AP(AIR-SAP702i). On the wired network, everything is ok. I've enabled IGMP snooping but no lock.The router i'm using is a 889G-LTE.There is only one VLAN. Any i...
My client has recently moved one of their branch offices from the WAN to a site 2 site VPN setup between an ASA5525 and ASA5506. All traffic from the branch office goes over the VPN tunnel. After the move to the VPN the APs keep flapping with the fo...
Hi, does licenses of Prime Infrastructure 2.x will work on a Prime Infrastructure1.3? Regards, Thomas
My question is related to BYOD and Employee Personal Devices on-boarding. I am trying to implement ISE CA service for authentication of employee devices without using AD. Is PEAP-MSCHAPv2 compatible with Internal ISE user database? I really want to u...
Hi Friends, I'm really poor in WLC deployment. I need to deploy a new 5508 WLC into network as a secondary controller. The primary WLC (5508) has been configured as a single WLC as of now and working good.... Now I need to deploy the new 5508 as the ...
Hi all, We have a large number of 2702i's and 3602e's running lightweight code level 8.0.110.0 and connecting to a AIR-CAP2504-CT-K9 throughout all of our branches. Occasionally, one or two of them will drop their static address, and try to use a DHC...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |