Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have Cisco 1310 wireless bridge and i don't know how but its operating system is not working any more i have the operating system in Tar file but when i try to upload it to the bridge it gives me the below message and i cant figure out what the...
I want to log into cmx browser https://mseip:8081/Mario/jsp/admin/login.jsp The login returns: Account is inactive. Please contact administrator. I can not login with my admin account, how can i reset the passwort or reactivate it? I do not have any ...
Hi, we are using machine and user authentication , when machine at logoff the machine is authenticated so users can RDP to it but after logging in the remote desktop session goes down because after user authentication the machine gets a new ip addr...
Resolved! 5508 WLC HA pair and layer 3 roaming
Hey, We have a pair of 5508 WLC's configured in HA (primary/standby). We have a single SSID that we're broadcasting across each floor of our head office. The AP's are in flexconnect mode so users pickup an IP address from the DHCP range for that buil...
HiI am facing with the problem.How to choose the wireless router part number support the following:Support 802.11n/a/b/g standardOperates on both 2.4 and 5 GHz frequencySupport Power over Ethernet (so you don’t have to wire the power cable, just use ...
Hi, I've noticed that from time to time some of our flex connect AP's will join our less preferred 2504 anchor WLC instead of staying on the 5508 HA pair controllers. The 5508 HA (active/standby) pair are in the same mobility group as the 2504 to fac...
Hi everyone,I have a problem with my vWLC and AP 1602. I have the vWLC 1 with 7.4.121. software in cloud and 3 AP's 1602 and it is working fine. And I tried to make a Backup Controller vWLC 2 on Local network. I downloaded the cfg file, changedn the...
Hello Wireless Guys!I hope someone can give me an expert advice!There is an existing Wlan on many location around the world, the Vendor of this Wlans will be variable….sometimes Aruba, sometimes, HP and so on, I do not know! From the design view it i...
Currently, my D-Link DIR-625 Router is connected to Linksys CM100 Cable Modem.I want to replace the D-Link Router with a Cisco Aironet 3602i Access Point. Apparently, simply connecting the 3602i AP to the cable modem through Ethernet port doesn't wor...
I have setup wireless in camp as following:One AP1532E connected to wired network, three AP1532E configured as wireless bridges on Dot11Radio1 (5 MHz) interfaces and as root APs on Dot11Radio0 (2.4 MHz) interfaces. Some clients have trouble connectin...
Hello All, I'm wanting to do a Mobile IP demo for university and I have the following simple demo in mind - I would have 2 routers connected via a serial cable, with a LAN on each side. I'd have a Wireless Access Point on each LAN and set them so the...
Hi AllI am currently working on a WLAN migration from lightweight to autonomous and would like advice on whether the following scenario is possible.We've deployed an 8500HA pair at the customer's central HQ with the plan that SSIDs at the central HQ ...
Problem: If we create an AVC profile in the WLC to drop the traffic for bittorrent, Kazaa2 and edonkey , the traffic still goes through in release 7.6. I have a 5500 Series Wireless Controller and my main concern is how to drop an encrypted Bittorren...
Hello.I have a WLC 5508 that has the software version 7.2.110.0.aesAnd I have access points AIR-CAP3502I-R-K9 and outdoor AIR-CAP1552E-A-K9.All access points are set to country code RU, that is done so that 3502I points would work in bridge mode. Aft...
Hello I have 2 WLC in my company, 1 is backup of the other one.When i first connect the AP to the network, it is getting attached to the backup one, how can i cange it?However, the AP is connected in the same network of my production WLC, also, when...
