Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi guys,I have a faulty secondary 7510 controller (on HA) and going to replace with a new one. How do I go about this?What steps should I take?Anyone done this before? Thanks in advance.
Hi everyone! Here is my topology and I need to perform image recovery for my 3602.3602 can be connected and powered only by 2504 controller.How I need to configure controller to allow communication from 3602 and TFTP server???Does all ports on contro...
Greetings, id like to deploy some 1530i access points in bridge mode between two points located ~250m apart, however i'm unsure of the range these AP's will support using the internal antennas or whether the beam with is small enough to cover the dis...
What is best way to handle or setup wireless connection for a small branch office with less than 10 APs? Management doesn't want to spend any money to install a local WLC. Those APs will communicate back to two WLC 5508 in Data Center.Should I use...
Is there any way to set static relationship parent & child in WiFi Mesh Network? I know all the MAP and its RAP must belong to same BGN.
Hi Cisco TeamI would like to confirm cisco 5700 series wireless LAN controller can be worked with other vendor AP.I have Aruba AP and Ruckus AP that can be worked with Cisco 5700 Series WLC.Please give me help to buy cisco WLC.Best Regards
Hi all,Can anyone advise if this device runs Linux or OSX based software?1900 series (1921) integrated services router I have been asked to check if this hardware is possibly at risk from the shellshock bug. Many thanks,James
Hi guys, I have two CT5760 so but just one of them came with a stack cable. Can I do a HA connection with just one STK cable, I friend of mine intentend to do this ask yesteday and he sent me this output: WLC#show switch stack-ports summarySw#/Port# ...
Earlier this month Cisco released a new autonomous IOS for the 2700 and 3700 access-points. If I look at the release logs, they reference to a new 1700I access-point:Support for Cisco Aironet 1700 Series access point- This access point is built on 3x...
Hi,I am having issues with wireless client sticking to its existing associated AP until the connection speed drops to 1 Mbps or the client dis-associates. At this point the client goes out to join the AP its closer too. Its a Warehouse environment wi...
Hi Folks, I'm currently working on a post site survey for a hospital to see what there coverage is like. They want it to be VOIP and RTLS ready. I'm looking for ideas or advice, especially in how to cover the elevators and stairways in each floor? ...
Hi all !I am currently looking at the Cisco 3850 Catalyst+WLC. I saw that they could be stacked, but you can only have 50 APs registered.What happens if you link 2 3850 using HSRP ? I suppose you'll be able to register up to 100 APs, but when you wan...
Hi Everyone, Our question here is how to upload AP license, file .lic into AIR-CT5760 WLC?The interface inside too much different with WLC 4400 and WLC 5500 series.I have experienced before to add AP license for WLC 5508 series. And I thought the pro...
Resolved! LAP1142N-A-K9
I am new to this, so please have patience. I purchased an LAP1142N and can't seem to get the Configure Terminal command to work after I enter the "enable" command. I get the "Invalid input detected at '^' marker" error message. I did notice that wh...
Is there anyway to audit the access points in FC mode to determine the WLAN-VLAN mapping and if it is AP or WLAN specific? or Is there a script that I can run to make the WLAN-VLAN mappings on all FC mode APs AP-Specific?
