Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello Team, I have an issue with BYOD authentication as user is able to connect with SSID and receive IP address but webpage redirection is not happening and Logs shows L3 authentication failure. WLC: C9800 Authentication server: Clearpass. Attaching...
Hi Guys, i have some reports from clients that they occasionally loose connectivity during authentication to EAP-TLS enabled SSID (that is using AAA override to steer them into correct vlan / flexconnect setup) I've tried to check the live logs on th...
Hello, So, I was migrating very old wireless network devices (WLC 5508 and Ap 3602I) at a customer site. Customer purchased WLC 9800-L-F and C9136I-ROW AP. We decided to use 17.12.3 as the WLC software. The software being marked as Cisco suggested re...
I am having trouble finding maximum distance documentation when installing two MR76 with Omni antennas on a pole. I see documentation saying they need to be at the same elevation, but I don't see a reference as to the maximum distance they should be ...
Resolved! VPN: tunnel data to a concentrator
hello, just a questin regarding VPN: tunnel data to a concentrator for SSIDLayer 3 roaming with a concentrator is clear , the client is projected in the vlan directly attached to mx appliance and gets an ip from a remote DHCPwhat happens when using V...
Resolved! WPN VLAN
Hello again,in one of our networks we have configured an ssid with WPN access on all floors.All devices are using the same VLAN, because they are all part of the same group policy.Now I want that on one floor, all devices in the same ssid are in a di...
Hi, I need a solution that can isolate clients from each other on a Cisco Meraki MX64W model.So far I have found how to isolate clients from different VLANs. Maybe someone has managed to isolate clients from each other in separate VLANs?
Hello, We have a handful of WLC 5520 units in our lab being prepared for deployment. We are just working on getting AireOS updated from 8.10.132.0 to 8.10.196.0 via the SP GUI, and getting this error: We noticed the same issue in this bug report: h...
We have a wireless network, created from Meraki CW9164i APs (Current version: MR 30.6). It advertises three SSIDs: Corporate, Guest and IoT on 2.4 and 5GHz. We do not (yet) run 6GHz, though that is our intent in the near future.In one area of the net...
Hi,I received a 9163E Access Point and with it being an outdoor model I expected the casing to be fully metal. I was surprised to see that the lid is plastic and after removing it states it is polycarbonate and weighs approximately 250g. Its stamped ...
All access points with MR 30.6 version do not show the splash page when clients connect, the solution is to downgrade to MR 29.7.1 version.This only happens if you are using splash page redirection.
Hi Folks, i have question regarding setting mobility tunnel between wlc 9800 and 8540, i need to anchor the guest network back to 9800 wlc. my concern is if i do that would that cause any issues given that the guest network on 9800 is configured unde...
I need to configure static IP on the BVI1 interface but the interface keeps resetting. I get the notification %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
Hello everyone, when I try to join the AP on the 9800 (17.12.4), I get the following message: Nov 16 07:39:12.187: %APMGR_TRACE_MESSAGE-6-WLC_APMGR_INFO: Chassis 1 R0/0: wncd: Info : - Qos not available for wlans 3, for AP KE-AP with AP MAC xxxx Does...
Resolved! Antenna parameters and gain in EWC
Some doubts about antenna gain and parameters in EWC. I can't understand why is so complicated: I have to check which antennas the AP are using (A, B, C, D) and the antenna gain in 0.5 dBi units. Cases:1. I connect an AP C9115AXE with 4 antennas ANT2...
