Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi, I have configured the Cisco ISE 1.2 with all the basic configuration.And now am trying to connect from one ssid from my laptop .Am not be connect to that SSid.checked all the SSID configuration in the system also in the controller It is telling l...
I have 4 Cisco WAP321 access points, connected to a Cisco SG200-26P switch, operating in PoE mode.3 of the APs are fine, but I am having a problem with one of the APs, which appeared to be working OK, but the other day when I unplugged the Ethernet c...
dears, there is a huge warehouse, the customer needs to covered voice and data, my question is how to covered it while the ceilling of the warehouse is 20 m, and the racks (roofs) are apporx. 15 M. the racks are too long. if i select omni i think is ...
Hi Professionals,I am able to configure the EAP session timeout parameter on Cisco Autonomous AP and WLAN Controller (5508) but not on Cisco ACS Radius server.Can please suggest me "How to configure EAP session time out parameter on Cisco ACS 4.2". ...
The customer's wireless controller is currently supplying service for 802.11b, 802.11g and 802.11bn. Using the command line, is there a command which will provide the total of clients which associated using 802.11b only, not 802.11bn or g. Thank yo...
Hello All, I hava a WLC5508 with many OE602I APs,I find when i open the link MONITOR>Statistics>AP Join,the "AP Name" is not correct with the real ap's name,for example,the correct ap's name is AP028-617,but it display ap name is "AP028-617B9.0870[Et...
Hello, we have had a number of issues call quality with 7925 VoIP phones and think that a big part of our problem is that the "Wired QoS Protocol" field for our Platinum QoS profile is not enabled for 802.1p. When trying to enable this field we re...
Hello,I have an architecture with 3850(MA) and 5508(MC), i can show that the txpower is configured on automatic mode in my 3850. But i need to known the exactly txpower of my AP.Where i can find this information ? on the AP, or on the 3850 ?Thanks in...
We have a Cisco 8510 controller which is our centralized global controller. We have a site in Panama with numerous Access Points. 2 of them are randomly changing their country codes to Canada. There are other APs but only 2 are doing this about once ...
Dear Experts, I am not able to ping the ip address which are connected in the same Wireless network.what would be the reason for that. RegardsTD
Greetings All.I am facing a weird situation while configuring two wireless bridges (1530E) attached to a 14Dbi semi directional antenna.There's a clear line of sight between the two bridges and the distance between them is 3 miles but there's no asso...
Hi Team, Any one can share the LLD Documents for the Wireless lan controller Implementation. Regards,
Hi, I wanted to create one SSID using cli commands, on AIR-AP1230B-A-K9.Please find the attached my ap details in "ap info.png", To create the ssid(in open authentication mode ) using cli commands i had followed the below steps. AP1200(config-ssid)#d...
Hi all,I have an SSID where clients cannot get DHCP addresses. I have captured the following debug and from what I can see the WLC recieves the DHCP address from the DHCP server and then attempts to forward that to the Station but the station does no...
Currently in all Standalone AP enviorments we are able to use an OID to tell us how many Associations are on each AP and our system then sends alerts when we feel the load is to high.Since migrating some of our networks to LightWeight WLC and the AP'...
