Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Is it possible I can load-balance my client ? In our current setup when one AP down rest of the client move to other AP, we need to move them manually or connect/disconnect. I can apply max-association on SSID but is there way I can do it automatical...
Hi!I have a question about Cisco Wireless deployment.As i know, all traffic from AP tunneled to controller, and then goes to receiver.But in this case, if i have only one controller, it will be single point of failure.Is there any feature, which will...
Hi all,I have to replace 500 old APs by 500 new APs (with no change about the configuration, architecture etc). I would like to know if there is a way to automate new APs configuration like AP Group, admin status, mode (local, flexconnect), location ...
Greetings, With the recent introduction of IOS 8 for Apple devices, those devices which has been upgraded can't seem to connect to the WLC 3850. Further checking on the release notes I found out that the latest IOS version 3.6E ONLY supports till IOS...
I want upgrade vWLC from 7.6.130.0 to 7.6.130.2, but I can not find such image for vWLC. I can only find the upgrade image for WLC 5500(AS_5500_7_6_130_2.aes),but this image can not use on vWLC, when I down it I got error message 'Transfer Failure: t...
Good Morning,I am having trouble tracking down some useful information.Currently I am working through testing using AVC to mark\drop packets on our standard DATA WLAN. I would like this to work so i can put my best foot forward with marking our LYNC ...
Will the 2702 AP require the full 15W? Should a switch labeled as POE+ give every AP enough power? The HP procurve 2530-24G POE+ deliveres 195W but we're not sure if it can support all 24 ports.
hi all, I face a problem when i deployed Cisco Prime Infrastructure 1.2 and added my switches and routers on it, the routers are not seen in alarms. if i have a switch down it appear in alarms and when router down is not appear in the alarms ? please...
Can sleeping clients just be on anchor controller 7.6? Can the foreign controller not have sleeping clients configured and it still work as long as the anchor is configured for sleeping clients? The other question is.. Do all user use sleeping client...
Hi Folks, We have a setup the following solution for CMX- APs ( private network) at remote location connecting to WLC ( publicly available) throught NAT- WLC, Prime and MSE in a DMZ publicly available- APs and WLAN are configured for flexconnect loca...
I am cleaning up some older alarms in Prime and I noticed that there are some alarm types that have no place for a map to load. Why is that?
How can i change AP hostname for LAP via CLI?I got the error 'command is disabled' when i try to use command 'capwap ap hostname <>'I try to disconnect LAP from WLC, factory default, clear all private-configure and clear all files in nvram: but not w...
Hi everyone just a clarification about Fast Transition for me:Following environment: WiSMv2 with 7.4.121, al lot of 1240 APs, over 200x 7921/7925 WLAN Phones and few iPhone 5s / 5c with 7.1 iOS.The environment work very well for Cisco 792x Phones. No...
Hello, I was just wondering if the catalyst 3650 mobility controller could integrate with ISE in the same way that a WLC does. But on another note, what is the main difference between the 3650 and a WLC as far as features go? Cheers, Waqas
Hello,I have an issue with Cisco AIR-AP1231G-E-K9 since I have rebooted it to reload startup conf : Now, radio is disabled. On web interface, Radio mac address is 0000.0000.0000 I tried a no shut on Dot11radio0 but didn't work.I tried to upload a new...
