Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! WLC 9800CL N+1 Configuration
We've just configured out secondary cloud controller in Azure and I wanted to know if I need to configure anything in Mobility Groups or just configure my AP Join Profiles as shown below?Thanks!
Working on setting up a WLC and AP for SISE studies. I have the IP for the WLC configured and I can ping the gateway. I can temporarily reach the webgui then I'm unable to but can still ping the management IP. Also I can not ssh to the WLC. I manuall...
Hello,Does anyone have a dimensional drawings (preferrably a DXF/DWG version) of the Universal Mounting Bracket - Cisco Part 700-30482-05 Rev B0?Look forward to receiving any feedback.
Hi, customer need is to have wireless LAN extension between two buildings at 500ft distance.My suggestion is to use 2x MR86 + 4x ANT-MA-27Will this be sufficient, or should we start looking at other vendors?Maybe someone has already this setup and ca...
Hi everyone, I need everyone's advice. Does this solution work properly?For the building 1 floor 10, have 10 AP and 2 wIPS AP. AP joined WLC A (5520) and wIPS AP joined WLC B (9800) that integrates with DNA Center for aWIPS capability. Is it possible...
Hello everyone We have a Cisco Wireless Controller 2504, and we are having issues when trying to connect to a SSID with Web Authentication (or Web-Passthrough) configuration on Windows 11 computers. On Windows 10, iOS and Android works fine with no i...
Resolved! Why MERAKI AP are downloading a trojan ?
yesterday I got a notification about a MX event which has blocked the download of a Trojan malicious file.till there, fine and good to hear.But looking in details I discovered the source who downloaded it, is not a client but one of my MERAKI AP (wit...
Is there a troubleshooting checklist for a WiFi network that has next to no internet connectivity? I.e. steps to run through to isolate or eliminate specific potential root causes, from bad DNS configuration, to misconfigured firewall or content filt...
Hello, I currently have an SSID using 802.1x with PEAP communicating with Cisco ISE. We are using 9800. We plan on decommissioning this SSID and want to present a splash page after the users authenticate warning them that the SSID will be decommissio...
Hi everyone, We are excited to announce Cisco Wireless IOS-XE 17.15.1 Software Beta Program. This project enables following features 6GHz support for Taiwan & Guatemala New B/C/D Country support for C9163E AP Regulatory changes in UAE & Qatar Flex-c...
We have a future client who is trying to get information about the inhouse Meraki devices from there current MSP. There MSP has let there Fortigate licenses lapse and has told the future client that they are out of compliance on the Meraki devices b...
Hi All.We have a MR36 AP on firmware 30.6 connected to a MS120 switch.The AP is online and working but shows offline in dashboard.I can ping the AP from the switch.Dashboard message:This device may be unplugged, or it was connected to a new device as...
Hello, We're moving to Intune and trying to implement an Intune policy to authenticate devices using the NPS Radius server and on-premise CA certificate server. I would appreciate guidance on this.Thank you.
I need to downgrade the firmware of an AIR-AP2802I-Z-K9 from version 17.6.4.56 to version 8.10.151.0 but I can't find a procedure for this. What is the best way to do this manually with direct console access on the access point?
I recently configured a Cisco Catalyst 9800. After setting up the device via the console, I enabled the web server and configured the management interface along with user credentials. SSH access is working perfectly, but when trying to log into the w...
