Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Should I upgrade my 2125 WLCs?
I have 2, 2125 WLCs in my production network with the system software, 7.0.98.0. I know this is pretty old but it's working for me. I need to purchase 1262 LAPs and although I read that software version 7 and higher should support them I'm concerned ...
Dear all, Just a simple question, but causes a change of the 802.11n MCS value settings on a 5508 WLC a reboot of the AP's? RgrdsAad Boelhouwers
Resolved! number of users per Access point
Hi community:Two questions about planning wireless setup:1- Is there a resource/whitepaper from CISCO that recpmmends the number of users per Access point ? I figure the model should also be taken into account.2- Any recommended tool to plan the loca...
I am in the process of installing a new wireless network in our offices and I was wondering if I can add an extension to the cable that connects my AIR-ANT-1728 to my AIR-CAP-3502e AP to get better coverage in our offices?
Somewhere I ran accross a command to log off a guest user from the CLI. I am now testing a new webauth bundle and would like to use this command - well, of course I can;t find it now when I need it! Thanks Wes
Resolved! Enable 802.11n HT (Greenfield)?
Hi all.I've just been tasked with setting up 19 AIR-CT2504 WLCs with AIR-CAP3502E APs. The primary objective is to maximize throughput from clients uploading LARGE files over the air.I need to make sure I config HT 802.11n properly with no support f...
Resolved! AP load balancing question
Hi there, is it possible to enable load balancing for a particular group of APs and disabled for the rest. Perhaps AP groups. Running 8500 WLC with 3600 series APs. It will enhance the service concurrent user capacities for areas with a high device c...
Dear Folks,I am looking for a solution in a hospital that can have wireless access for guest users . Guest users will be registered through captive portal page and password provided through SMS .Is there a solution on Cisco that can provide this func...
Resolved! 802.1X authentication and roaming issues
Hi there,I have installed about 2 days ago one Cisco WCS 2504 and 11 APs. Everything is doing well regarding to WEP authentication. But I have a Radius Server that is alson running with some issues on wireless: - Unless I open network settings and cl...
Resolved! 5GHz PtP link with 2600e access points
Hello,In the old days I used two autonomous 1242AG access access points to create a 5GHz PtP link with 2 patch antennas (over small distance 50meters and on on private premises) to connect an small building or garage were there was no ethernet availi...
Is it possible to take a AIR-LAP1142-N-K9 AIR-LAP1142N-N-K9 and convert it into the -A- version??? The N version does not allow editing nor does it support 5GHz in the US. I'm thinking we may be SOL on this as I couldn't find anyth...
https://supportforums.cisco.com/thread/2209827?tstart=0 Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about how to monitor, troubleshoot and configure Wireless Networks using Se...
Hi all,I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.I know we can see it throug...
We have a WISM in a 6509. The 6509 lost power (the UPS failed) and upon reboot the WISM isn't allowing AP's to connect. The WISM is blade 4. Upon consoling in, I get this error message for all 8 ports: 42w6d: %EC-SP-5-CANNOT_BUNDLE2: Gi4/1 ...
I have installed Cisco Prime 1.2 Infrastructure, with 6 5508 WLC's and a 3355 MSE, with Ap models: 2602i, 3502i & e, 1131, 1142. I am having issues when I am trying to add the access points to maps etc, and the server running very slow, I have confi...
