Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi all,I've tried to test the backhaul throughput using a mesh network consisting of two 1552 APs operating on channel 100. For this I've used iperf to simulate a transmission between one laptop connected to AP10 and a server connected to the same sw...
Hi good afternoon,I have an easy question, checking how WLC with AP associated making a tunneling in CAPWAP (standard RFC 4188) using a UDP dest port looks like its necessary L3.Let me try to explain what i want:I have a WLC 5508 with a Switch the t...
Resolved! CAPWAP/LWAPP config
Is there a way to change the username/password for all the APs connected to a WLAN in one move or command? Normally I would go into the individual APs and change the controllers in the WLAN GUI. But there's got to be a better way, seeing that I hav...
hey guys.i'm in the process of moving 2 miles outside of town. The company I work for has a large tower on the edge of town that I have a clear line of sight to from my new house. We don't have any options for high speed internet access, so my idea...
HiOur radiology department has recently recieved a couple of Arcadis Varic devices and so we tried to connect to our network wirelessly, but it constantly failed to connect. The error messages in ACS was "11500 Invalid or unexpected EAP payload recie...
Hi all,I want to be able to send snmp traps to my NMS alerting our NOC to when we reach our configured max-associations on an ap. We currently use both 1130 AG and 1140-2N in autonomous mode, no controller. I have found a debug command "debug dot11...
Resolved! WiSM crash with no crash log
Guys,I have many WiSM WLC's running 7.0.116.0. One WLC was rebooted few days ago but there was no crash file and nothing in logs say why this issue happened.There was a power problem at the same time the WLC rebooted (some switches and PE's was reboo...
Resolved! MSE 3310 Requirments
Hi team,My customer currently having WLC 5508 and Cisco 1142 Access points. Now we are going to by AIR-MSE-3310-K9 for wIPS purpose. Do we need to buy WCS also or MSE will work without WCS. ?Regards,Naisam
Resolved! Cisco AP1121G Workgroup Bridge Problem
Hello,For reference I have attached the following:Network DiagramPing Results TableConfigurations for 1811 router, ap1121g root access point, ap1121g wgb.I am seeking assistance with the following problem.Referring to the attached network diagram, I ...
Hi,We have AIR-LAP1141N-E-K9, that will be installed above false ceiling made of "perforated aluminum" with 1mm thickness with 17% open slotted surface.What would be the level of interference and signal loss?Many thanks,Yazeed
Hi all,Our organisation has multiple controllers at regional sites (one per region) & want to implement redundancy by placing one controller at headquarter's datacentre as a backup in case the site's failed.All our controllers are 5508 with 7.0.116.0...
Hi alljust been given a CAP 3502i access point, try to logon and configure the password, but not accept the config t. Is it because this equipted with Light weigh mode IOS?I followed the link bellow: http://www.cisco.com/en/US/docs/wireless/access_po...
Is there a reason why my configured interface group don't show up when I run a 'show run-config commands" on my WLC?To specify: If I run "show interface group summary", this will be the output:(WiSM-slot4-2) >show interface group summaryInterface Gro...
hi,what is 802.11a/b/g/n standards?is there any document available for this?I also want to know basics of wireless like RF, channeling(what it is and how it works?) help me on this
Hi AllI have set up an ACS (5.2) to do EAP-TLS Machine and User Authentication.I am getting intermittent results with the machine authentication using the same laptop as a test client.When the machine authentication succeeds the RADIUS name shows as ...
