Having trouble getting started. I can get the ip set. Then ping successfully. Open my browser and enter the new address - and get connection interrupted.I'm low tech - just trying to set up an access point with no security.
Having trouble getting started. I can get the ip set. Then ping successfully. Open my browser and enter the new address - and get connection interrupted.I'm low tech - just trying to set up an access point with no security.
Both boxes are running a linux kernal. Can a WLSE be used as a location appliance ? Reuse of a apliance that would have other wise been scrapped.
I have a 526 controller and 4 521 APs on my LAN that I want to upgrade to LWAPP. I am using CCA and all the help says this should be a point-and-click type of thing. However, when I try the upgrade the CCA asks for an image I don't have and can't f...
The documentation is a little fuzzy on what is supported. Does anyone know if H-REAP will work with the 1131G Access Point?
Hi,we just install a solution with 10x AP1131ag controlled by a WLC.We setup different WLAN with different authentication settings (web authentication, wep, wpa-802.1x).We notice that the radio signal power is really poor and even if we install many ...
HiToday I reinstalled the image in a cisco access point, however since that I cannot use http to access it, it comes up with a screen with very basic commands. What do I need to do here?cheersCarl
I seem not to be able to convert a 1252 from LAP to Autonomous. Anyone know if any issues with performing this task on the 1252?We are using the following document.http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/...
I have 1250 LAP and I want to install my own Sertificate on LAP because I want to have secure LWAPP communication between LAP 1252 and WLC 4400. How to install may own certificate from MS CA to LAP? I have already installed certificate from my MS CA ...
I've inherited our current WLAN that consists of two identically configured 1121 APs in separate buildings. Authentication is WPA-TKIP PSK that requires manual configuration of all devices. Guest access is handled through a separate VLAN that has A...
Any ideas what is causing this particular message in the logs of our AP's.It only seems to affect the odd user, but always the same user getting kicked off. I have tweaked the countermeasure to stop everybody getting dropped, but the cause of this is...
I used AirMagnet Planner to place 1242 APs in warehouse using 35mW and -65 dBm cell edges with 20% overlap for 7921G phones.I plan to use RRM and Dynamic Power Levels. However I noticed when manually setting the power I can choose, 1 thru 5. With 2 5...
We have over 150 AP's installed. 1. I am noticing the below type of PING times from various clients attached to various AP's at different locations. Very few locations r reporting <2ms. Reply from 172.26.5.111: bytes=32 time=106ms TTL=127Reply from 1...
Is anyone using EAP-SPEKE password authentication? I have just been reading about it and can't find out if cisco ap's will support it?SAM
Hi, I'm trying to configure a mobility group between 4 WLC's. 2 of 4 form a group and those two are the two on the same cards.The two cards are on separate subnets and each have are connected to a FW. I've opened up for UDP12222-12223 UDP16666-16667 ...
I have been asked to make some changes to a 1310 AP at a new site. When I try to browse to the device, I get the login screen, but when I put in the username and password it say :not authorized. I can telnet into it and the username and password work...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-16-2024 12:50 PM | ||
08-15-2024 04:04 PM | ||
07-17-2024 11:11 AM | ||
07-17-2024 06:04 AM | ||
07-08-2024 04:04 PM |
User | Count |
---|---|
20 | |
11 | |
6 | |
4 | |
3 |