I have 4 new 9120axi-b access points that are showing the duplex at full and the speed at 100.show interfaces wired 0wired0 Link encap:Ethernet HWaddr .....53:30UP BROADCAST RUNNING PROMISC MULTICAST MTU:1600 Metric:1full Duplex, 100 Mb/s Is there a ...
Forum Posts
hi everyone, I hope someone can help me. I bought a used WLC 2504 with version 8.2.130.0. Now I want to connect AIR-AP1242AG-E-K9 access points to the controller.The AP also finds the access point, but then returns the following:Cisco IOS Software, C...
Hello,For some unknown reasons, the WLC instance has been removed from our smart licensing portal.I tried to register again our WLC 5520, and forced it, but now we have this status :Smart Licensing is ENABLEDRegistration:Status: UNREGISTERED - REGIST...
HiThere is no connection between WLC to LW-AP and there is no capwap connection as well. D1interface FastEthernet0/1switchport trunk encapsulation dot1qswitchport mode trunkswitchport nonegotiate!interface FastEthernet0/2switchport trunk encapsulati...
I unpluged the cisco AP port and again I pluged it but The AP can not join the WLC*Feb 28 04:15:04.001: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.17.5.3:5246*Feb 28 04:15:04.102: %CAPWAP-5-AP_EASYADMIN_INFO: AP Easy Admin information...
Hello,I would like to ask you about a light access point that can't reach a WLC 2504 controller.The access point has an IP (with the DHCP server of the controller) but remains in "not joined" status on the controller.Would you have a solution please ...
I a setting up a Guest network on 9800L WLC. I have it setup to the point where the user can join the network but no redirect page pops when they join. I am able to see in DNAC that they IP learn is successful and L3 Auth starts but on testing no Red...
Good day colleagues! I have a one interesting question, in my opinion, about embedded IoT-BLE in c9100 WiFi APs and DNA-spaces architecture in general. To be honest I couldn't google this answer and couldn't find anything about it on cisco.com, stran...
After applying an upgrade to current version 17.06.05 on our two C9800-L-F-K9 devices (not in HA), one device won't boot anymore... LEDs are off. Powercycling let the onboard LEDs light up, but switching off after a few seconds, fans keep running on ...
Resolved! External antenna and coverage problems
Hi,we use a WLC 2504 in an old museum with thick stone walls, with 4 intersecting tunnel-like corridors/hallways and several rooms and little halls connected to the corridor.Besides two CAP2602i internal access points which work fine, we use a CAP260...
Hello, I'm looking to se if there is a way in order to disable just the 2.4gHz band on a single model 3802 AP in out environment. Were running a model 5520 controller. When on the controller & I check the AP in question under Access Points > Radios ...
HICan I use CBS350 POE switches in ENT wireless network to connect WLC 9800L and C9105AXI Is CBS switches support that connection and can work smoothly with CAPWAP and other wireless protocols and WLC functions
Hi All-We are exploring ways of keeping our internal devices off our our guest network. Guest is open with no authentication or sign in required. I was thinking of trying to use MAC filtering to accomplish this. I think this will require a pretty...
Hi,we have som vsat location there we need to find a block high data usage clients, because we have very low bandwidth. I have figured out how to block clients, but I am struggling to find the high data usage clients mac address. Is this possible on ...
It seems that a new feature called 'Easy PSK' is supported as of WLC version 17.5. Looking at the description in the documentation, this is something that could potentially be interesting for our environment. The documentation about the specifics on ...
