Wireless

Does anyone know a procedure for resetting the enable password on a AP521 access point ?

I have 1252 autonomous APs acting as non-root bridges and 1242 autonomous aps connecting to the 1252s. I wish to lock down which 1242 access point can associated to which 1252 access point. I don't want the 1242s to roam.Any suggestions on how to con...

Hi everyone,I'm looking into a project to cover a large residential area with wifi using the 1500 series access points on 2.4Ghz and using a 5Ghz backhaul.Before I go ahead an organise a site survey I'm trying to get a rough idea of the coverage dist...

Good afternoon,Anyone have 802.1x standalone ap wireless example with guest vlan and valid vlan? I need the configuration of the wireless and switch port. When user to try associate and accept, valid vlan, not accept guest vlan ( or ssid ) i don't k...

Hello,I have some ap's here that are connected to the controller and I'm connected to those ap's and surfing the web with no problem. However, they will not show up in the WCS. I can search for the ap's mac and ip, nothing. I've also searched for ...

Hi Sir,My customer has the following unified wireless guest access requirement:- There are 2 internet links and dmz zones at two different locations, Site A and Site B- Data centre is at Site A- WiSM is proposed to be installed at the Cat 6500 in Sit...

Hi All, Is it possible to deploy WLC redundancy over L3 link???In our scenario we have 2 controllers located in 2 different sites, the link between the site is L3. AP's are deployed across four other locations, two are coming to site 1 and rest t...

I have 2 WiSM blades (4 controllers) in a 6513. The goal is to upgrade from 4.0.179.11 to 4.1.185.0 which requires an intermediate step of 4.0.206.0+.I upgraded the first controller to 4.0.219.0, and now I can ping the WiSM and can session into it f...

Hello:I just installed a 802.11a/b/g card with winclient version 4.2 installed. after reboot, i could not even get back in the xp system any more. before the loading the driver, the system didn't require password, now it pops up "log on" and ask for ...

I am getting the following error below from a 851W router. Any ideas as to what is causing this?Not encrypted dot1x packet from 001c.bf83.2a21 has been discarded

Hi,I try to configure a WGB in autonomous mode to connect to a lightweight access-point. I followed the cisco paper about it and my wgb associate well to the AP on the asked SSID. From the wgb i can ping stations behind the lightweigth access point s...

Hi,I'm using cisco 4402 with a few AP's to boardcast SSID and manage all AP's. I want to know is there any way for me to get alert when someone can successfully connect to my network instead of login to the management console to check?Thank you!!!

I have a LAP1131G-A-K9 with C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, System image file is "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"I need to revert from LWAPP mode to autonomous mode but I don't know what IOS should use.Any suggestion?

Hello All,Does anyone know if there is a way to get the WCS or WLC to report if a change had been made via syslog or snmp? Also, is there anything specific that has to be configured in the WCS to send emails of traps or alarms? I see where there ar...

Anyone know where I can get this module?http://www.cisco.com/en/US/docs/wireless/wlan_adapter/eap_types/fast/admin/guide/EF_instl.htmlAlso, can I use EAP-TLS or EAP-FAST (with certs only, no PACs) and authenticate users via LDAP (AD) without the need...