Wireless

I have two buildings that are just out of line of site...I need an antenna that can go through a couple of trees....the trees are not on our land so we cannot cut them down. I am using 1300 series Wireless Bridges.Thank You

wlc4402 5.0.148.0 Windows clients have very poor access to network resources inside of our network. The wlan is on a tagged interface associated to a port that is a vlan trunked port on our 6509. If a wlan that is associated to our non-tagged managem...

Hi,I have all of my WAP's connected and managed by my WLSE but it showing that they all have the same name under Devices > Group Management as well as when I try to deploy new templates. If I dig into device explorer it shows the "Full Name" as the w...

Hi Folks, i had to use the WCS Planner to make a quantity structure for a new Building. This Building has some Inner Courtyards, where WLAN coverage is undesired. How can i exclude these Areas from the Map in the Planner Tool? Any Idea? What is teh D...

i have a cisco air-1230b-a-k9 access point accidentally it was lost it's ios.while i tried to load ios through xmodem it is showing me that no space left in device. though there is no file system in flash

I have a customer that has asked if he can import an AP configuration into WLSE and create a deployable template from it for additional AP installations?

Just wondering if anyone has ever seen these logs on there controllers before and if so what do they mean?Oct 30 09:39:50.839 apf_foreignap.c:1278 APF-4-REGISTER_IPADD_ON_MSCB_FAILED: Could not Register IP Add on MSCB. MSCB still in init state. Addre...

Ive got a WLSE and a bunch of APs, Can I push out a command from the WLSE to update all the APs so that they are prepared to support DST this weekend? Or do I have to do this manually for every AP?

LAP,power-supply is AIR-PWRINJ3error message is output in wlc,how can i resolve this ???thanksLog System Time Trap 0 Wed Aug 13 23:40:58 2008 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:1f:26:2a:b1:f0 Cause=Radio Low Power 1 Wed...

Hi,I received an AP1131 from my custoemer who said it just quit working. I checked the configuration in CLI and Graphic Interface where I found a message in "interfaces" that showed Ethernet but radios 0 y 1 said not installed. I reload the version b...

Hi guys,i have a 2106 WLC with three 1131AP LWAPP.I should cover a zone where there is no network cabling and i was thinking about another 1131 in mesh mode.Do I need particular software release?Can anyone provide documentation from which i can start...

Hi guys,I have a 2106 with a non mesh release and four 1131.I need two oh these 1131 work as RAP and MAP so i i understood well the steps required are:1)Donwload a mesh release2)Once Ap are controlled change their operative modeDo I miss something?Th...

I am configuring some AIR-LAP1242AG AP's with a variety of external antennae. I notice within the WLC the antenna gain should be value which is then "x 0.5 dBm". My question is for an AIR-ANT4941 antenna, which is a 2.2 dBi Dipole 2.4 GHz, what shoul...

Cisco have been kind enough to lend us a 4404 WLC and I've got to grips with setting up our WLANS on it and I can get an AP to pick up config from anywhere in our extended network.I am, however having a problem trying to get an access point to join t...

I have trouble capturing lwapp data frames. I have AP on port 1, i have instructed my switch (3750) to monitor this port and send it to a available port on the same switch (no stacking). On the second port , i connect my sniffer. I see lwapp control ...