Wireless

hello to all...i have connectivity like this:Host1---AP-trunk---Cisco2950-trunk--LinuxVLAN2 | | Host2--- |VLAN3i have created 2 vlan on AP... and fastethernetport of the AP is connected to the cisco2950 and cisco2950 is connected to the ...

I have not been able to get WiSM controllers on 4.x code to detect a wire-side rogue with open auth (Cisco AP and Apple Airport Express). It did find the open Airport AP once when running 3.x code, but has not since the upgrade.Has anyone succcessfu...

I have a WLC 4400 in a remote site and I need to reset it to Factory-default. The service-port is connected to a switch and it can obtain an ip-address from it. I don't have a remote console access. Is it possible to do the inizial wizard configurati...

I've confured a new site with 4 radiobases AIR-AP1231G-E-K9 c1200-k9w7-tar.123-8.JA2.No Vlan, WPA, TKIP,(The same config as many other sites).Authenticating to a central Radius.My problem is that I cant move around whithout losing the connection. I h...

After AP1232 convertion from IOS to LWAPP -> following error Message*Mar 1 00:00:44.216: %LWAPP-5-CHANGED: LWAPP changed state to JOIN*Mar 1 00:00:50.217: LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not recieve the Join response *Mar 1 00:0...

When i add ip address 10.100.100.1 255.255.255.0 secondary to interface Bv1 and i type show running-config i can't see secondary ip address.Why?Many Thanksap# sh verCisco Internetwork Operating System Software IOS (tm) C1200 Software (C1200-K9W7-M), ...

I'm hoping someone can lead me to the right document or show me some example config to have my 871w use MAC address authentication. I currently have it setup to use WPA successfully, but for added protection, I'd like to use MAC address authenticati...

Hello,I use freeRADIUS to authenticate WLAN Clients. Traffic is encrypted with WPA and clients are authenticated with LEAP or PEAP.The AP 1220 with IOS 12.3(8)JA2 works well and the configuration is the same for PEAP and LEAP.The value "Session-Timeo...

Hi,I was wondering if anyone knows if it is possible to vnc to remote vpn clients that are assigned an address from a client IP pool defined on the pix.The remote clients are using cisco vpn client, the access-list is a dynamic acl downloaded from a ...

I am planning a rollout of dot1x using mac-address authentication with SecureACS v4.0. Does anyone know if there is a way for ACS to point to a database of mac-addresses so I don't have to update it manually (say a machine is retired or a new machine...

Hello,Sorry for my English, but I am French and I do not speak very quite English.I will like to know which is the VCI string for an AP 1232AG to inform in the 43 DHCP Option.Could you help me ?Thank youBen

int BVI1ip address 10.0.1.1 255.255.255.0ip address 10.1.1.1 255.255.255.0 secondary Need the radio int on a different network from the ethernet int. Planned on using a secondary address on the BVI int.I've had no luck adding a secondary address to t...

I've been beating myself in the head trying to figure this one out and I'm sure it's an easy one. I keep getting a "WLSE failed to authenticate with WDS" error for my primary WDS APs in all my sites with a couple of exceptions. We have a second WLS...

I do not any knowledge or experience on WLSE. This is the first time I have heard of this product. Customer says that he is not able to see or manage this one CSC AIR-AP1131AG-N-K9 11a/g but can see and manage other Access Points. He tried to delete ...

Looking for a "recommended" design. Looking at a remote location that contains no Cisco switches or router. 5 AP's total. Seems kinda of pointless to setup a 4402 Controller for 5 AP's. What is the recommended REAP mode implementation (real world)...