Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I am not to familiar using TFTP to upgrade the IOS on the Aironet access points as I have always done it via the GUI. I have Solarwinds running with my IOS in the root dir and the AP connected via console cable. Everytime I attempt to upgrade via the...
I am trying to configure WPA2 with 802.1x authentication through ACS 3.3. Having issue with using PEAP authentication through ACS 3.3 configured for Novell NDS as External Database. Client is stuck "Verifying credentials". Controller sends authent...
Do anyone got any knowledge of Symbol & how they fare in marketplace vis-a-vis other more well-known players ?
I have three Cisco 1310 bridges, one root and two non-roots. I have posted my config below, br1 is the root and br2 would be the non-roots.My goal is to carry 4 VLANs across this bridge, however with this config I get "Uplink to parent failed: Unsupp...
APs get IP addresses, but VLANs do not work. Switches look ok with trunking, etc. The SSID works, I get good signal, but no IP, via DHCP or hard-coded. It did work at 1 time, but no longer.
The 4400 will not respond to a ping from a PC workstation on it's management address; is that normal?
I only have 1 Wireless laptop connecting to my 1131AG with latest firmware. I keep seeing this in the log.Interface Dot11Radio0, Deauthenticating Station 0013.cecc.8e16 Reason: Sending station has left the BSS It loses connection off and on.Any thing...
We're seeing a lot of 350-series APs (with updated IOS ver 12.2(15)XR2 from VxWorks) with interface resets on the Dot11radio0 interface.Can anyone explain what causes an 'Interface reset' on the Dot11radio0 interface? What happens to wireless client...
Resolved! Problem on ACS Solutions Engine (4.0)
Hi. I'm currently using an ACS SE4.0, WLC 2006, 1130AG LWAPP APs.My authentication in WLC is set on WPA2. No Layer 3 security.I also added Radius server pointing to my ACS SE4.0 and uses port 1812. I have user defined on ACS SE4.0, configured to sup...
Hi. Do any one now if the wism card is supported by cisco works
Hi there,Currently I have 3 Linksys wireless routers one on each floor of our office.WRT54G - Wireless-G Broadband Router However, they are not working very well, and continuously dropping connection.We are looking for a more corporate robust wireles...
Is it possible to secure the configuration of wds ?I have configured two ap´s with wds. Priority is set to 200/199. So the AP with priority of 200 will be the wds master. What happens if a new ap will be installed configured with wds and priority of ...
hello, is there a another way to query the AD besides installing CSACS in a member server or using a remote agent? if yes, how do i go about it?thanks.
Folks,I?m configuring PEAP with AP1131, ACS 4.0 and AD ( Windows 2000 ).I used the follow doc to do this:http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_configuration_example09186a00801df0e4.shtml#acs-1Please, see the logs ( ACS, AP )i...
Hi,I need to setup a wireless access on the 15th floor for 5 users. On the 15th floor we have 50 LAN users connecting to cat4003 switch and this switch is trunk to the cat6509 switch located in the data center in the basement where the servers are c...
