Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I have a network with some Cisco 1200 Series AP´s. This ap´s have 802.11G radios. When I configure a new template, in the last pass (SAVE) I receivedthis message:Error processing template configurations. No valid device versions supported. This is th...

acamara by Level 1
  • 854 Views
  • 6 replies
  • 0 Helpful votes

Hi there,I'm trying to synchronize my Cisco Access Points (AIR-AP1232AG-E-K9) Clock with our time server (win2k SP2).In the Web interface of the AP I can only enter an IP address an switch to "enable" but he is not synchronizing. I only get the follo...

Hi there,What we have now is 2 offices (A and B) 150 meters apart."A" has the server farm and the main WAN link. I just want to extend the lan of A to B (using 2 Aironet 1310 bridges which I already have), in a way so users in B can reach A (servers ...

alk1000 by Level 1
  • 375 Views
  • 1 replies
  • 0 Helpful votes

HiI want to create a wireless bridge between two rooms in the same building. Can I do this with two Aironet 1131AG access points?Any useful information would be much appreciated.

Hello all,I have an aironet 350 series wireless card for my compaq iPAQ H3970. It is setup to use a server-assigned IP address but is having problems doing so.I have looked up troubleshooting documentation for this and a software reset of the device ...

Does anyone know any means to perform traffic recognizion/marking/classification for LWAPP traffic on per packet basis? Is it even possible? I'd like to recognize voice traffic from inside LWAPP and give priority treatment for it...

preinist by Level 1
  • 397 Views
  • 2 replies
  • 0 Helpful votes

For the most part, I have been installing the Linksys residential access points in my business. These are not doing the job in a recent install at a hotel/condo. I was wondering what Cisco access point would be appropriate. I can put a couple per ...

Hello all,I am trying to implement WDS w/o WLSE. I simply want to be able to be to have an AP in scanner mode report detected SSID's to the WDS device. I have a few questions about this:1. How does the scanner-mode AP report this information? (SNMP...

mcwoods by Level 1
  • 422 Views
  • 1 replies
  • 0 Helpful votes

I have my access-points AIR-AP1231G-E-K9 with IOS 12.3(2)JA2 configured in wpa mode.I have a notebook xp SP2 with cisco AIR-CB21AG-E-K9 card.The PEAP authentication is managed by windows and works on a cisco ACS version 3.3.The problem is that if i e...

giga01 by Level 1
  • 333 Views
  • 0 replies
  • 0 Helpful votes

Hi,I have an AP1231 I firstly configure this AP with a single SSID with wpa encryptions and also configure it to act as a local DHCP server. This all worked fine, with clients picking up and ip address etc.Now I need to configure 2 SSIDs, each with a...

asiclari by Level 1
  • 483 Views
  • 2 replies
  • 0 Helpful votes

I have setup a AireSpace 2006 with 3 AP's for wireless Internet Access at my site. Our SEcurity Folks want to be able to look at the GUI as a IDS. I have found that the 2006 has IDS signatures but I cannot find what I need to configure to make the de...

lhoyle by Level 1
  • 373 Views
  • 1 replies
  • 0 Helpful votes

Even though WLSE 2.11 does not support the new IOS 12.3(7)JA, I tried upgrading an AP to 12.3(7)JA using a WLSE upgrade job and it worked just fine. I ran the same job on about 10 APs, one AP at a time, and it worked every time. What is the max num...

estein by Level 1
  • 594 Views
  • 4 replies
  • 0 Helpful votes

Hello,We have several 1200 AP's via dot1q connected, and Cisco PCMCIA adapters. It is possible to see some information of the AP via 'connection status'.Connection status gives e.g. the Access point Name and ip-address. I dont' want to give this kind...

vos123 by Level 1
  • 304 Views
  • 0 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card