Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I am currently not able to ping or connect to a share on any wireless clients on the WLAN.running cisco 2006 wireless controller, 1000 series cisco AP and all desktops are runnning linksys WMP54G wireless cards.anybody have any ideas?
I'm debating whether to connect my Cisco 1231G and 1242AG stand-alones to switch ports set to 100 Full or set to 10 Half. I'm told we'd be able to do error checking if we set the switch ports to 10 Half, and that 100 Full wouldn't give us much of an ...
Per doc, the Airespace support multiple vlans and 802.1D, but it does not specify the trunk encapsulation for WC port 1 or 2. So what would be the switchport configuration for Cisco switch, trunk or access? We try to deploy 45 AP with multiple WLAN (...
We have cisco aironet 1100 and 1200 and when some peoples try to connect with Itel Chip wireless cards they can not connect and come to us and we can not solve this problem yet. so if you know some information for this subject please sen to me.
I have SSIDs configured on 1231's to support WPA/WPA2. They work fine with Cisco cards/supplicants but intel proset cards (2915ABG for one / I tried the latest drivers from dell and intel) seem to have issues. They will see the SSID and associate, bu...
Hello,nomebody could tell me why I can see in the module association (web mode) on my Aironet 1200, an ip adress 0.0.0.0 associateThanks for all information
I've recently picked up one of these and have upgraded it to the newest IOS revision from VxWare. the first thing i've noticed is that i can only select 30mW/max as the top radio output... after searching all over these forums, i've only found one th...
Windows Client <==> Access Point <==> Radius <==> Windows DC/AD Windows OS : XP Client SP 2 Supplicant : Built-in Wireless Supplicant Authentication : 802.1x PEAP(MS-Chapv2) Access Point : Aironet 1200 Radius : ACS 3.3 Adaptors : Built-in CA : Micros...
Hi, Does the Aironet AP 350 with IOS 12.3(7)JA support CISCO-IETF-DOT11-QOS-MIB? I checked the 12.3(7)JA configuration guide, it supported. But I tried to use MIB browser to queried, it told me "no such object".Best Regards,
When configuring WEP with CKIP/CMIC, broadcast key rotation had to be selected separately within the AP configuration. Does WPA by default include broadcast key rotation or do I have to configure it?Also, is it beneficial to select any of the values ...
I'm not able to get a Wi-Fi card to connect to a cisco AP1200 when everything is setup for WPA-PSK/TKIP. The Treo 700 sets on "connecting" and the AP generates an auth_failed error.I know PSK is right on the AP and treo. This is not a new wireless de...
I have a client who is seeing fairly consistent problems with their 7920 phones aquiring a DHCP address. The phone boots and associates to the AP quickly, but then stalls on configuring DHCP. After a couple of minutes the phone gets a DHCP address an...
I am unable to get some of my clients to pull DHCP addresses when associated to my APs when I have VLANs configured on the APs. Once I delete the VLANs my clients can pull IPs, but when I put the VLANs back on they can not pull DHCP addresses. I an g...
Hello all,I have a PCI a/b/g card that was working but, I had to re-install windows on this PC and now the card shows packets transmitted but, none received. I am using the 2.5 drivers. My 1100 ap shows the card is associated. It passes the network t...
HelloDuirng roaming (we use for auth. leap) between the 5Ghz to the 2.4Ghz and vice versa we lost up to 5 pings. Roaming in the same band we just lost maximum 2 ping. We have 1200 and Cisco a/b/g Cards. Is it recommend to have profiles on the wireles...
