Wireless

My main AP is a BEFW11S4, I setup a Aironet 1100 (12.2(4)JA with the same ssid, station-role repeater, parent 1 mac x, however the LED on the 1100 is flashing rapidly.show dot11 association doesn't show the parent ap or any association.Any ideas? Wil...

I am setting up several 802.11g access points. They will be configured to only allow my 802.11g (Linksys WET54G) clients associate. I have configured my Cisco 1310 APs not to allow 802.11b connection rates. Has anybody done this and how well did it w...

Since upgrading two 1200 ap's from vxworks to IOS...I have been seeing this alert on my remaining vxworks 1200 ap's not on the two that have been upgraded to cisco IOS. I have not been able to find any rogues. Is this a bug? Also, I am wanting to upg...

I have a AP1200, with Aironet Ext. off. Radio is configured with all Data rates to "enables with 1.0Mb/sec set to "required"I can not connect with some built-in Toshiba 802.11b cards?, My cheap SMC 802.11b card works? And the g cards work also. Not s...

hi!i configuried 1310 , but it is strangely.if between root and not-root is 9km,it is failed.appending my configuring. is it right ?1. 1310 (root)interface Dot11Radio0 no ip address no ip route-cache ! ssid tsunami authentication open guest-mode infr...

I have a Aironet 1200 IOS AP running on my network. I am having a problem where I never receive DHCP information to the clients associated to the Access Points. All hardwired clients are working just fine. I get the standard 169 address when getting ...

Have a PP link with 1310BR, set up SSID and WEP as a minimum. Been noticing in event log that there have been associations with MAC addresses unknown to our network. Appears that they are accessing our network, but why would they associate if I'm not...

Certicom has announced that it will no longer support the movianVPN client for PocketPC as of Oct 31, 2004. That was the only client that I was aware of that worked with the Cisco 3000 series concentrator. Is there another option available? Will Cisc...

I have Cisco AP-1230b and Linksys WAP11 v.2,6. This Linksys work in APC mode. It conect to Cisco AP-1230b but it is no transmision of data. Why ? I dont know.

Network layout is as followsrouter 10.0.0.1AP1 10.0.0.2 (cisco 1300 in root ap mode)BR1 10.0.0.3 (cisco 1300 in workgrp bridge mode)AP2 10.0.0.4 (cisco 1200 in root ap mode)[router]--ethernet1--[AP1]--wireless1--[BR1]--ethernet2--[AP2]--wireless2--[w...

Hi Everyone ! I've this network:INDOOR:1 Ap 1200 802.11b with 2 standard Rubber Duck 2.2 Dbi antenna configured as Root unit.OUTDOOR:1 Ap 1200 802.11b with 2 omni antenna (AIR-ANT 2506) 5.5 dbi configured as Repeater2 Wireless Terminal PSC Falcon 345...

I am trying to get two workgroup bridge 350's to work together. I have one pc at each end and I want to ping the other. What is the minimum conifuration that I have to do in the 350s in order to get a ping to go across and atleast know that they are ...

HelloI've this scenarioWinXP wifi clients+ Freeradius + Cisco AP1200. Everything works fine but when the option 'WEP rotation' is enabled sometimes XP clients have problems and the authentication fails. Maybe ,during 3-4 hours it works but suddenly a...