Wireless

I'm having a problem that started recently with my WLSE. Whenever a fault occurs with an AP, I receive the standard "Device was not reachable by SNMP" error message. I'll check out the problem and correct it but the fault will not clear from the "Dis...

Hiif anyone can helpo it would be great.I I using a cisco 350 within our building for laptops users.We are using no servers for authentication.I want to only allow our mac addresses to authenticate with the access point.I also want to encrypt our dat...

Hello,I am setting MAC filters on my AP 1230. Althought it seem to be working, when I enter a MAC I see no errors at all but when using both the IOS or browser to see my current configuration I see different MAC addresses than the ones I type in the ...

I have an 1200 series AP, and when i try to associate it as a repeater, it associate and disassociate many times per second, and after a while, it gets blocked or shuts down. I have configured the same authentication type for both (root and repeater)...

Hello all.I have an aironet 340 access point and several aironet pcmcia client adaptors. I have a laptop running win nt4 server and the rest running win nt4 client. How should I connect and setup the various devices such that all these laptops can fo...

Dear Sir,Does the AP handle load balancing dynamically?I know that the client will switch to another AP based on the signal quality level detected and not on signal strength. How about the utilisation on the AP? Will this play a role? If I have 3 APs...

I have a bridge that I'd like to use as repeater to connect to an AP in root mode. Is it posible to do this? or viceversa? The access point (in non-root mode) connecting to a bridge in root modeThanks!

Receving this message when client attempts authentication....Any idea or pointers on troubleshooting this? "EAP-TLS authentication failed during handshake"

Hello all,I'm trying to use EAP-MD5 as the authentication mechanism with my Aironet Card and the Microsoft 802.1x stack under Win2K. Unfortunately, this choice is not possible while I can do it with legacy LAN cards. According to CCO litterature, it ...

Deployed 22 AP's and have 100 plus coming down the pipe. Had to manually manipulate the config .ini file foe all 22 AP's to configure them. Once I was completed I had to make serval changes. Now I dont have a valid config file to restore an AP is it ...

Could you please explain why my AP 1230 is getting 2 IPs from DHCP server.after show ip aliases, I see:Address Type IP Address PortInterface 172.16.43.45Interface 172.16.39.98Could not understand why? what is BVI1 and how it differs from the Ethernet...

We are piloting the Cisco VPN 3000 client and have had several reports of loss of network connectivity afer the VPN 3000 client 3.6.3(C) is installed. At least one report was on a Windows 2000 (5.00.2195, service pack 3) laptop that was running Airon...

Hello,Newbie to VPN's and security.Securing our WLAN environement with about 50 Cisco 1200AP's, 65 SpectraLink VoIP phones, various wireless users. Currently have a seperate Wireless VLAN. Will be putting this on our corporate VPN. Is there any other...

Background:Cisco 350 Aironet Card (driver version 8.3.10.0)SecureACS 3.1 (auth to AD) Windows XP SP1aACU utility with PEAP Supplicant (6.00.023)ACU is setup to manage Wireless access.I get error message:PEAP failed initialization, status = -16 error ...

I'm trying to setup PEAP authentication of XP users through 1100 access points to an ACS 3.1 Radius server. I know that I can download the client utility for the client side or use MS (suggestions?). I need an installation guide for the access points...