Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello all, I have a troublesome PCM350 PC card that can not associate with any AP's. All troubleshooting steps followed. Is there a way to set the card to factory defaults. Or does anyone have any other idea before this hits the graveyard.
how many non-root bridges are supported by one root-bridge (point to multi-point)?1) root-bridge have ant-2506 omni antenna2) non-root brigdes or work group bridges(ant-1949 yagi) are in the ant-2506 omni antenna's coverage.3) the number of associate...
We are investigating a solution to provide wireless access to public places. It is kind of not practical to require the client user to have Cisco ACU software in order to configure LEAP on his wireless card. Does LEAP work without the ACU software on...
Hi!I try to setup an AP1100 for getting the time from an W2K Server via NTP .But it will not work. I did the same with an BR350 and same W2K server, this works fine. Any Idea?Than you,Rouven
Dear SIr,Can LEAP support single login to windows via LDAP? I read through an article published in Cisco website saying that LEAP only supported in Windows NT/2000 Active Directory.What is OTP, one time password compared to single login password?CSAC...
I'm implementing a large WLAN for a hospital. they will be using Cisco VPN and RSA OTP to provide authentication and data confidentiality/integrity. They also desire a Wireless LAN Solution Engine.I wish to create a "user" VLAN-SSID mapping, and a "w...
I have a bit of a conundrum, I have a client associating to an Aironet 1220 unit, the problem is - the client appears to have a DHCP server on his side, and to have plugged the bridiging unit (A Smartbridges Airbridge) into the ethernet switch. The i...
Hi,We installed a WGB 20km away and forgot to configure password on it.Could anyone tell us, how to configure remote a password onto the WGB to secure the http-access?thanks ins advanceAugust
I'm trying to configure my 1200 Series AP with 11b and 11a radios to perform as a "local authenticator" for LEAP clients. I've started by configuring the normal RADIUS server as the AP itself; and then configuring the local authenticator, with the AP...
What is the limitation number of clients (PC or Switch etc) that should be connected on to the wired LAN end of a Wireless network ?Wired LAN (SWITCH)<------>AP/Bridge <-->Antenna
Has anyone implemented PVLANs on a large wireless LAN network to limit broadcast traffic? It is expected that almost 100% of the traffic will go off the VLAN to different subnets so intra-VLAN traffic will be minimal at most. Without having tested th...
A 340 wireless bridge which is configured as an access point mode can be connected to 340 wireless bridge which is operating as bridge only mode with the root mode is turned off.WEP is turned off. No MAC filtering enables. Both SSID are the sameHowev...
I need a way to completely reset the 350 to a factory default config. The buttons on the web interface do not do a complete reset. My vlans still exist after the reset, and this is not desirerable. I'm sure there are other settings still hanging arou...
Can anyone point me to some documentation on how to configure CiscoSecure ACS 3.1 and the wireless clients to work with wireless VLANs? I'm trying to use an Aironet 350 running 12.02T1 to test wireless VLANs, and the documentation I've found so far s...
I've searched everywhere for this message showing up in my logs and can't find it anywhere. "BKeyXmit radio is not OK" It occurs every 90 seconds. Firmware version is 11.10T1.
