Hi everyone, I have a Cisco WLC 2504 that doesn't allow me to access via SSH. The network is ok, I can access via web GUI and console cable. The configuration seems correct too.C:\Windows\system32>telnet 10.x.x.x 22Connecting To 10.x.x.x...Could not ...
Hello Community, I have two APs on is a bit older - AIRCAP2602-l-i-k9 and the other is AIR-AP1815W-E-K9. First I bought the 1815 with the idea to run it as a controller for my network, but turned out the console cable for this bad boy is hard to find...
Hello,I have a series of AP model AIR-CAP3702I-E-K9 in lightweight mode connected to a Cisco 8540 controller. The curious thing is that some of them have 5GHz enabled :AP001# show interfaces dot11Radio 1Dot11Radio1 is up, line protocol is upHardware...
We have a 1562D RAP with three child 1562D MAPs associated to 8540s. They are used as bridges with several VLANs trunked across.This morning, I upgraded one of our 8540 HA pairs from 8.10.183.0 to 8.10.185.3. Everything was working from about 4:15am ...
I am encountering an issue with my SSID, which has WPA3 Personal enabled with RADIUS for employee authentication. When attempting to connect my iPhone, I receive an error message stating, "Can't connect to this SSID." However, after forgetting the ne...
Do we have any option in Meraki dash board- If the AP goes down it should send a e-mail Alert
HiI have a bridged network that will be available to all but i want to restrict availability 9-5 to specific users. So by default block users at that time unless they are allowed.Is this possible without adding a policy on every device.I was looking ...
Hello.We have an environment consisting of 2 Cisco 9800 WLC. One primary and the other secondary.In addition, we have approximately 800 Access Points. All 800 use the primary controller. I just upgraded the secondary controller and now the primary ne...
Hello all, I am not able to understand how to enable the 4 switch ports in my 1815i. I am using this AP as ME controller for another one 2602. As the 2602 is old I am able to support only up to 8.5 with no issues. But there is also a bad side. I am ...
Hi,I've set up an SSID to use Local Auth for RADIUS with an LDAP server for authorization. I'm using 802.1x with the suplicant passing machine certificates issued by our own CA. Everything is working and clients are connecting, however in Windows 10 ...
Am I missing an easy setting on a 9800 cloud vitrual controller to allow the voice path between to remote workers on cisco phones, the call rings but and connects but there is no audio between the sets. I do not have an access list set on the rlan...
I am researching Cisco EWC APs. After reading some of the documentation, I am a little confused. The initial configuration, assuming we have separate Employee and Guest SSIDs / VLANs / Networks, notes the AP should be connected to a switch via a trun...
I use the default webauth customize from the following link:https://software.cisco.com/download/home/286316412/type/282791507/release/16.10.1However, the javascript loadaction() function is not working:function loadAction(){ var url = window.loca...
I have a Cisco 2504 WLC and 3 Cisco 1142n access points on my test network. The 2504 WLC and AP's have been off for a few months and I 'm trying to put the wi-fi back online. I am just learning how to configure this system. The 2504 WLC boots up oka...
Hello,I've been working with my company's consultant to upgrade our old Cisco 5520 WLC pair to our new Cisco 9800-L pair. We have attempted to mirror our current environment. We have two SSID's, one for corporate devices and another for contractors/...
