Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I've got a customer using Symbol 6948 clients w/Cisco 350 APs running 11.07. It appears that the Symbol clients seem to always want to go to the AP that's on Channel 1, even though there's much closer APs that are on channels 6 or 11. All the APs are...

ertrqueen by • Frequent Visitor
  • 1639 Views
  • 5 replies
  • 0 Helpful votes

I expeirience problems with a wireless link (Point to Point), while running a large amount of ICA sessions. When reaching approx 600 packets/s on the link, the radio starts throwing packets, resulting in "frozen" ICA-sessions, and users "throwed out"...

jhenes by • Community Member
  • 971 Views
  • 1 replies
  • 0 Helpful votes

Hi all,In warehouse or manufacturing environments where there are a loarge number of clients and a large number of APs (350s in our case), the 350 seems to wait until the quality of its association is really lousy before it tries to roam to another A...

bpowell by • Community Member
  • 775 Views
  • 0 replies
  • 0 Helpful votes

I wnat to connect 5places by cisco wireless product all are 40km in distance . If i use point to point then it is ok but if i want to use multi point to Point then what are the product I have to use can any one help me ... I am looking for it badly.....

Hi -- We are using Aironet 4800 AP's thoughout our factory. I have been told that you should not attach different antenna's to the same AP. In other words, do not attach a dipole antenna on one side and a patch antenna on the other side(both should b...

rx33328 by • Community Member
  • 1050 Views
  • 2 replies
  • 0 Helpful votes

I am setting up an outside network to be used mainly by handheld devices (Ipaq using the the PC card adapter). I am thinking of using the Aironet 350, but I need more range than 2000ft. So, I was thinking of using the Air-Ant4121 to extend the range,...

swisst by • Community Member
  • 1099 Views
  • 2 replies
  • 0 Helpful votes

With all the talk of 802.11a products on the near horizon, I'm wondering about Cisco's plan for this technology. Will there be support right away for speeds less then 54Mbs? (I hear the max will be at 90ft). (Are other speeds in the standard ?)Is Cis...

I am interested in a bar code scanner that will run Windows CE, be programmable using something like Java, VB or C and supports Cisco Aironet Dyanmic WEP. I would like to run Cisco Secure ACS against my Windows 2000 A.D. and authenticate the user of ...

rkeblusek by • Level 2
  • 1387 Views
  • 1 replies
  • 0 Helpful votes

Can anyone help me with this?I am getting CRC errors on a few of my bridge access points that are in the range of 90 to 200+ CRC errors every 10 seconds. This is only on the radio side, not the cabling side.I have a 4th floor office and am using brid...

paul.hoffman by • Community Member
  • 2374 Views
  • 5 replies
  • 0 Helpful votes

I am looking for documentation regarding traps for mainly the radio side of 340 & 350 Bridges and WG Bridges. Especially signal strength / quality and connect rate. I have some MIBs loaded, but the AP MIB's are all that appear to be available for thi...

j.retterer by • Community Member
  • 910 Views
  • 0 replies
  • 0 Helpful votes

I am confused, when using Leap does the Wep key get changed each time the client device roams? What kind of time delay does this cause. Does the Access Point give out the new key or do you have to go all the way back to the Radius server to get the n...

dteet by • Community Member
  • 1079 Views
  • 2 replies
  • 0 Helpful votes

The 'SSID1' field gets changed to all vertical-looking bars or boxes when the client associates with the AP. I can change the SSID back to 'johndoe' and it associates, then unassociates. If you go back into the utility, the SSID is changed back to th...

gino by • Community Member
  • 925 Views
  • 1 replies
  • 0 Helpful votes

I have two Aironet 350 APs installed in our Enterprise wharehouse. I keep getting the error message "Network Bridge Loop: Received packet from Self destined to [AWC Mcast All]014096ffffff on port "fec0" on both AP. Is there some extra config that mus...

cmd1 by • Level 1
  • 1278 Views
  • 4 replies
  • 0 Helpful votes