I've been reading about WLC's lately and I will begin labbing to set up some WLC netorks. Overall I am new to network engineering, my normal profession in forensics. I read a lot about AAA servers, RADIUS, ActicveX etc. If I were to get hired...
Forum Posts
Hello, I have an issue with my AP 3802i in the Discovery State. I want to say I'm new to networking stuff just learning things. Here is my issue [*11/09/2018 05:27:20.1838] CAPWAP State: Init[*11/09/2018 05:27:20.1843][*11/09/2018 05:27:20.1843] Con...
Hi,When we are preparing for the heatmap what all the factors should be included.If I am planning an wifi 6 heat map , what is the maximum and minimum power should be selected ?Thanks
I just set up a Cisco 5508 WLC and a 3702 AP. The AP is in flexconnect mode. Both the link to the WLC and AP are trunks. Both are using VLAN 255 as their managment ip. Facing the AP I used "switchport trunk native vlan 255", and am able to reach it o...
Dear Engineer & Professional, Can it be possible to config AP can working without WLC?For now, our AP is sending and receiving data by a Cisco Wireless Controller 2504 so when WLC is down, all of AP stop working. I would like to config AP to working ...
HI everyone. I have 41 AP (AIR-CAP702I-E-K9) controlled by a WLC (2504) distributed on 3 different floors. On each floor there are three AP that are not connecting at 1Gbps the auto settings for speed and duplex get them to 100Mbps.I've troubleshoote...
Hi folks,I want to know if CCNA Wireless 200-355 is good enough to cover the basics of ENWLSD and ENWLSI or we need to study this course Understanding Cisco Wireless Foundations WLFNDU v1.0 to improve our Wireless Networking basicsAppreciate your rep...
Resolved! add wireless on gns3
Hello, I would like to add a WLC on GNS3, but I come across a message that says I need a license to be able to download. Is it possible to get it for free? If yes, how ?The message :To Download this software, you must have a valid service contract as...
I have a Firewpower 1010 that has 2 POE ports 1/7,1/8 that have 53.5VDC voltages. When I connect the 140AC access point it will not power on and according to the specs its requires 48-56V. I am using FMC to manage this device. I am not using a POE...
Hi , I would like to configure Cisco Aironet 4800 series AP. Please help me to find the actual installation process.
I am working on creating a voice vlan for our Cisco WLC that I have had setup and working well the past few years. We currently have some wirless 8821 phones and I want to create a separate vlan for this. Currently they are running on a layer 2 vlan ...
Hi everyone, we have encountered a possible compatibility issue with client's receipt printer when connecting to RLAN enabled access point. i was wondering if you have encountered this issue before or have some inputs that may help resolve this issue...
Hello All, I have an ap model of AIR-AP3802E-B-K9 which cannot join the WLC, I have performed reset on the AP and yet it does not join the controller. It picks an IP address but registering to the WLC is the issue. I have attached the log from the AP...
We are trying to carry out a design for a client with a large warehouse that is full of pallet racking. They have specified the Meraki range of AP's so we initially worked on using the MR76 with a MA-ANT-21 to cover a 50M aisle using 5GHz only. To pr...
Hello Engineers & Professionals, Does Cisco provide trial file for 9800 series of Wireless controller as a virtual? Our company is considering to purchase new controller next year, but I would like to look around some functions before we actually pur...
