Hi everyone, I plan to use C9800-L as a Radius Server with a local user database created manually on it.However, based on the specifications, I am unsure of the maximum number of users that will be supported.Can anyone please help answer this questio...
Several APs are being disconnected. CAPWAP DTLS session closed for AP, cause: DTLS server session shutdown Does anyone know the cause?
I have a MAP AP that connects to a RAP AP through Wireless Backhaul and then to the WLC. I am trying to figure out what switchport, WLC, AP settings need to be in place to connect local network clients to a switch connecting to the Mesh AP. All RAP...
Hi all, It's been reported from our internet SIEM team that, one of the client connect to Meraki access point traffic is seen towards 192.0.2.1, I did go to clients and verified however not seen any client with 192 series IP address. Can someone sugg...
Hello Team, I hope you are all well.I hope you can help me with a problem I'm having with an EPSON L365 printer. We have this printer at a remote site that previously connected via WPS to the ISP's internet router. Now we've added Meraki devices (MX,...
Hi guys: I have this AP that I need to move from one client WLC to another. I dont have access to the original WLC but I do have access to the new one. I tried to do the swap on the AP configuration but it was tied to the older WLC and I did not have...
Hello Cisco WLAN expert,in the dawn of a planned SW-Upgrade on our 9800-80-WLC 17.9.5 it was suggested to reboot all APs on beforehand.Unfortunately several 9130-APs did not survive the procedure and struggle to boot up again correctly apparently. W...
Hi Community,I thought I'd put this in to ask, essentially, we're needing advice in terms of the usability of an MR76, ANT-76 for creating a P2P between two locations, the variables are:1. The main site is 200M away from the existing MX that is conne...
We have a 9800-40 HA SSO pair running 17.9.5 controlling almost all 2800-series APs with a handful of older 3702I APs. The 3702I is no longer supported after 17.9.8. We purchased all new 9172I APs to replace them, but those are not supported until 17...
Hi,I can't see profile of new AP on ISE.Can anyone help me create or Import new Profile for AP CW9176I. We have ISE 3.1 for AP profiling. Thankyou in advance. Regards,Aamir Bhatti
Hi Guys; We have a pair of 9800-40 in HA SSO with RP only. When we first installed it was version 16.12.4. We upgraded to ver 17.3.3 patch 4 and want to enable RMI+RP. Which is the correct procedure? Enable RMI+RP under Administration-->Device, assig...
WIth C9800-L-F-K9 model, i have a Anchor and foreign setup with mobility tunnel formed between them. It is observed that if i switchover anchor WLC (HA-SSO), the mobility tunnel does not come up. I tried changing mobility mac to static.the WMI gatewa...
Hi there, I'm currently using CISCO AIR-CAP3502E-C-K9 APs that already has Autonomous software in it (ap3g1-k9w7-xx.153.3.JF5). My concerns is that, using internet source that has 150 Mbps bandwith, when connected to the AP, the AP can only deliver b...
Hi guysWe were just about to procure some wifi 6e 9164i and 9163e access points, however after speaking with Cisco it appears wifi 7 is now the way forward.We will need indoor and outdoor models, I see the 9172i might be good and the 9174i is also to...
Hello, how do I reach CCW-R? Is it from within CCW, or there is a separate link?
