Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi CPU ACL are configured at wlc 3504 to remediate security vulnerability. We cannot find the difference between before and after making the config change. The ACLs are listed as below where ip address 10.10.10.20 is the wlc management interface. Any...
I recently purchased a CISCO firewall 3000 series from a Third party seller. I called CISCO to help me track down the CAD files for the firewall but redistributed to community.cisco.com. Cisco or the third party seller are unable to provide me with t...
Hello everyone, On a site equipped with 2 AP571, I encounter a big latency concern when the posts go from one AP to another. Terminal 1 to 100% reception, I go to 2 point, it goes down between 30 and 50%I think I'm still connected to terminal 1.After...
I'm trying to disable a specific client from accessing our wireless network, but there seems to be an issue in disabling that specific mac address. Not sure what's the issue. I can disable any other mac except that one. Tried using gui and cli, same ...
As best practice, is it a good solution to do a reboot Wi-Fi controller and AP Cisco for sheduled reboot Is there a guide in the Cisco that talks about restarting Wi-Fi controller for refresh, for example, every month, or sometimes every quarter ther...
Hi, Could you please help me with below issue, when we are trying to register few LWAPs to controller getting below error on LWAP. few LWAP got registered on same switch.We are able to ping the controller from LWAP. log : *Apr 27 21:51:48.999: %DTLS-...
Hi All.I want to know how to take backup on Cisco Wireless Controller Via GUI.Engr.Waqar.
Greetings, Due to Cisco's ridiculously long delivery time, more than a year, we used a virtual controller for foreign and anchor inside 1 UCS. Now that the C9800-80-K9 are arriving we have to migrate the APs and 1 way we are looking at is to manual...
Hi C9800 wlc is setup. The interface Tw0/0/1 is configured as management interface. ssh and gui can access the wlc. but we reconfigured the WLC from scratch using Te0/1/0 as management interface, GUI cannot access wlc again. Is this because we are us...
Hello Meraki Gods.May you please assist asap? My users cannot connect to the Wifi network.When I run a RADIUS test on the AP’s, it’s all good:But trying to connect on wifi (happens to many different pc’s and users), just gets stuck here:Or here:Somet...
Hello everyone,I'm currently experiencing a concern about 3 laptops that only connect to a specific antenna in a cluster of 4 APs.In an office is an AP571, and 3 of the laptops in that office only want to be attached to that AP.As soon as I get away ...
HI we have wlc 3504. Its management interface ip add is 10.10.10.10. Via CPU-ACL, if we deny all traffic except port 12124-12125, 12134-12135and port 443 for ip address 10.10.10.10.the config can cause blocking access to the WLC?Thanks
Is it possible to automate the LAN port enabling of an OEAP on 9800?When you add the RLAN profile and policy you choose the Port ID but I still have to manually enable the port on every AP. Is there something is am missing so it automatically enables...
Hello,We have multiple 9800 and EWC and we are looking for the best RADIUS configuration. 1. How to configure Radius server priority ?In legacy AireOS WLCs we had the possibility to choose the priority order of our servers.With 9800 and EWC I didn't ...
Hey guys so we have around 8-10 cisco 9130AXI-G APs un our basement floor, they are wall mounted but the issue we are facing is that we are not able to connect to those APs on the basement floor, but are able to connect to those APs on ground and 1st...
