Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Buenas tardes colegasQuería consultar si es posible conseguir la imagen para convertir mi AP LAP1142N autónomo, ya que el mismo no tiene soporte como para activar el Smartnet. Gracias.
CMX upgrade 10.5.1-27 to 10.6.3-105 HA pair CLI or GUIquick question, performing my first upgrade of our CMX system(Conscripted into it, being the new engineer )I was checking to see how other folks have upgrade. I know I need to break the HA pair,...
Resolved! Cannot add some used APs to WLC2500
Hello,I move to a new location some 2 years and someone from this forum helped me to setup my WLC2500 to the new location.This was a used WLC from the old location with different ip range.He also helped me and showed me how to add some Aps which I di...
Resolved! Throughput shown on Mobility Express Network Summary from Capwap 3702Es with no client associations
I have ME 8.10.142.0 setup with 4x3802s and 2x3702s. On the ME Controller's Network Summary screen for the APs I'm seeing Throughput from the 3702s with no clients associated. When I disable the radios on the 3702s the Throughput drops to zero. The 4...
Hello. I have trouble configuring mDNS for AirPrint services on EWC.What i have:Fully fuctioning 9120 AP with EWC controller on it, software version of EWC is 17.6.1b. Connected to trunk port on switch. Printer resides in different VLAN from WLAN cli...
Found this particular question online. Pasted it on the lower part of the body. Can anyone explain to me why letter C, passive client, is not the correct answer here? it should be based on this link. https://www.cisco.com/c/en/us/td/docs/wireless/con...
Hi, Can anyone help my issue. APs can not join mobility express controller. Attached are the boot log, etc.
Hello.I've got AIR-AP1815W-E-KE. I read the official Cisco manuals and guides about configuration and what puzzles me is that the GUI shown in the pictures is completely different than on my device.Here is an example:GUI from "AP 1815 Wall Plate Depl...
Resolved! Guest not getting login page
I have gone through the documentation on setting up Guest wireless. We want to have the user enter a username and password.We are using Aironet 2802I access points with Mobility Express - version 8.10.151.0I have configured the guest network.Under WL...
Hello Expert,In my new deployment, I register my switches(MS) successfully and then connect AP to the switch.AP getting an IP address from the DHCP server which I see on the switch ARP table. and I ping AP from my all switches but when I ping from AP...
Is there a freeware SW to view installed access points ?
Does anyone know the technical difference between the AIR-MOD-POE and the AIR-MOD-SPOE. They both appear, separately, in different versions of the documentation for the Aironet 1800s module. When I configure an 1800s in a CCW estimate, currently, o...
Hi Experts, We have a SDA environment, the Sponsored Guest Portal (Login Page) is created and pushed by DNAC to ISE. The behavior we are seeing is every time our wireless guests connect to the network, they complete the sponsor flow and also see the ...
What is best practice to wire a Cat5e cable (4 pairs) with an RJ45 at one end, and a LSA+ at the other, which only uses 2 pairs?How does one best "wire" or isolate the unused 2 pairs?Many thanks
Were looking to upgrade from 3.9 to 3.10. Can you complete the upgrade using the CLI?
