Does anyone know of a bug that causes an SSID to broadcast even when disabled? We are rolling out our enterprise wireless and discovered a disabled SSID from two different 4800 access points. It cleared when the devices were rebooted. Using InSSID...
Forum Posts
We have a 2802I AP that is showing as connected on the switchport. It was only pulling 15400 watts. I manually set the power consumption to 26000 watts and then restarted the port. I then reverted back to power inline auto and now it pulls the cor...
Our 2802 AP is configured for logging to a syslog server on facility local0 and severity informational. On the syslog server we are not receiving logs at all. In TCPdump we see that the APs are logging facilitiy local1 and syslog10. Our 1142 and 350...
Hi, I have a wireless network with only one AP 1832i. He is master controller and runs the Mobility Express firmware withthe release 8.5.151.0.Now I tried to join a new bought AP 1832i (= Lightweight Access Point) in the network but after hours the j...
Resolved! maximum client count for 1852
Can I give the maximum client count for 1852E / 1852I as a document or url?
Hi Guys, I have WLC 8.3.122.0 and there are around 245 AP join the wlc. I noticed the issue when the client move from AP to another AP I noticed that the DNS removed and take long time for client to access the internet around 2 minutes. What could b...
Hi , i have three wlc'sin the network In order to accommodate 2802i access points in the wlc(ABC) ,planning to upgrade the wlc -ABC to 8.2.151.SIn this case please confirm whether the anchor wlc(BBBB) needs to to upgraded to the same IOS?Is there is...
Hi, I am trying to get my head round how a WLC works at a basic level and I just cannot figure it out. Can anyone please explain to me the following scenario we have: An SSID named "Ipad_WLAN' which uses local MAC filtering so doesn't look at ISE at ...
There is a rather annoying error in my AIR-WLC2112-K9. I upgraded to 5.1.163.0 and I changed 'ap-manager' and 'management' interfaces to untagged, but nothig helped. The only port that is connected is port 1.The error is:*Feb 10 20:24:47.744: %SIM-3-...
Hello! I have a Cisco 2504 WLC with 5 APs and 3 SSID. I have a problem with some users, the WLC disconnects them constantly and when I see my logs I obtain the next error: Thu Feb 23 14:31:06 2017 WPA MIC Error counter measure activated on Radio wi...
Hi all,Im working to develop a mobile network with the follow infrastructure Hosts 3 and 4 will be static point (cabled points) but, hosts 5,6 and 7 must be mobiles (satellite connections). Would be necessary to create an ad-hoc network with this top...
WLC is reporting extremely high channel utilisation and interference on 5GHz for one of our older 2602i WAPs. There are no connected clients on the 5GHz radio and there are no interferers being reported by CleanAir. The channel utilisation and interf...
I have a Mac Book Pro in a corporate environment that continues to connect to a AP at 2.4 ghz when there are 5 ghz AP(s) with higher RSSI and are physically closer to the client. An example: Client will (usually) connect to AP "A" at 5 ghz for an 1-...
Dear Experts, Can someone help me understand that when we connect to wireless, a speed value is shown which is probably the data rate at which i have connected. How this value is derived? My value right now is being show 130 Mbps. I can see its poss...
I'm trying to set up a DHCP Pool for a Cisco 1542i AP using the GUI. When I input the following information and press apply it just goes to a white screen and seemingly deletes all the info I just input. When I revisit the DHCP tab it's reset to the ...
