Hello,I have a setup with a WLC 5508. The APs are in local mode and I am using a radius server to autoassign VLAN and to authenticate the users via 802.1x. I have created all vlan interfaces on WLC controller.Some of the clients are complaining that ...
I am running into a very strange issue. Trying to setup and ACL rule under Advanced > Security Settings on the 140AC web interface. For some reason it will not accept the mask for the IP I entered. I don't see the problem. Did I miss something or...
Does anybody knows something like that. We are trying to do throuput test with ekahau and C9115AXI-Z, but the Ekahau does not recognized the WLAN that already are associated in the LAPTOP.
Hello Professionals,Our company is using WLC 2504 controller and most of WLANs can be used by registering mac-filtering.Some of users are configured 'Any WLAN' and specific interface in order to connect each WLAN for their purpose.However, sometimes ...
HiSo this morning we upgraded one of our Cisco 9800-CL clusters from 17.3.5a to 17.3.6.All C9115AXI-B APs (14) on a certain site did not join after the upgrade.The pre-download went fine, but when I finally got a console to one of the missing APs it ...
Hi All,I am currently planning the installation of a Cisco 9800-40 WLC that needs to be connected to two upstream switches for redundancy, however the two switches are not in a VSS or stack so the uplinks cannot be configured in a LAG. The two uplink...
Hello, My customer would like to migrate all APs in all sites to flexconnect. All APs on remote sites will join a central controller located in datacenter. Users will connect to a locally switched WLAN. 802.1X authentication with EAP-TLS will be us...
Gentsi need CTS inline-tagging enabled on the uplinks of my HA SSO 9800-L-F. sources i found so far referred me to jumbo enablement on the UCS-hosting platform (expectedly using CIMC access :0). failed to find how to access UCS's CIMC on 9800-L-F tho...
When o Access Point was in Autonomous, the interface was "state up protocol down" in "show int g0", so I change manually speed/duplex (100/full) and was "state up protocol up", so converting the Access Point from Autonomous to Lightweight and happene...
What is replacing the 1310 AP's in order to create a wireless bridge between sites?
I currently have two wireless controllers, a 5520 running 8.10.130 and a 9800 running 17.3.6. I need to move some of the 3802 APs that are joined to the 9800 over to the 5520. I have the cisco-capwap-controller DNS entry pointing to the 9800 and I ...
There is a warehouse with a height of 14 meters, a width of 3 meters, and a row length of 105 meters.I want to use C9120AXE-E and AIR-ANT2566P4W-R= per row.Do you think the choices are correct? Can I run into any problems?Is it right to use a interna...
Hi,i want to use SSL certificate for the WAP571 security. When i completed the upload, system said "The certificate file failed to be uploaded".what that means? and how to solution?Thanks.
Hello,In case I have to implement a wireless network with 15 Catalyst 9124 access points using the Embedded Wireless Controller solution, do I need to use the EWC AP image for all the 15 APs or just for those serving the primary and backup EWC role?T...
Hi All, I am looking to restrict per client user bandwidth for our Guest network on Cisco 9800 WLC's. AP's are in Flexconnect mode.IOS version is 17.3.5aIs this possible on catalyst WLC like Aireos based WLC's? -Kamal
.jpg "VIP Advisor"){kind=icon}
.jpg "Hall of Fame Guru"){kind=icon}
