This also includes a Cisco AIR-LAP1252AG-A-K9. These APs lose POE when switches in the building are rebooted due to power outages. When the switches are back online and booted up, the APs are still powered off. In order to get the APs back online...
Forum Posts
Resolved! New Interface on 2504 WLC
I have inherited a 2504 WLC (still running7.0.220.0) which has one corporate SSID defined.I intend to create a new SSID and interface for a guest network, which will be on a separate subnet and VLAN. The VLAN is yet to be defined.I am running into tr...
Hi,I would like to know what is the added value for the wireless health and safety site survey? Knowing that an AP cannot exceedthe maximum TX power for specific country.Could you please point me to the right document? I was not able to get clear vie...
It's my understanding that the MR32/33 allow IPV6, but unless bridging is enabled, IPV6 will not be used. Is this correct?Also, if I globally disable IPV6, does that require a reboot of the MR32 AP's?Or will IPV6 just cease to exist on the AP's and b...
A customer is performing the ipv6 implementation. the wlc is currently being configured, the ipv6 address was set in the management interface, this ip responds ping from the core, but from another vlan in the network does not respond ping. I would li...
Hi all.I am using WLC 3504 and AP air-ap3802I-F-K9 with firmware 8.5.151.0 configured as flexconnect AP. We have 3 SSIDs, 2 of them are using dot1x and the rest is PSK.Once a day, there is a random client (not happen to all client) having difficultie...
Hi, We are looking to buy a Cisco Aironet router in India and we found that part number for that is AIR-AP2802I-D-K9I.While our Singapore team has already a same router with part number:AIR-AP2802I-S-K9. Is there any difference in terms of technical ...
Ive set up a wireless network today consisting of Cisco 2800 WAP's and a 2504 WLC. For some reason the AP's will not join the controller. I have a consoled into the wlc and this is the output *spamApTask4: Jan 01 16:30:15.600: a0:23:9f:21:83:40 Deco...
Resolved! AIR-AP1242AG-a-K9
The company I work for just purchased one of these APs and I am having a hard time configuring it. I hae done several searches and I can't find what i'm looking for. It seems that after a factory reset by holding down mode during power on, that I can...
We are trying API based login using app in WLC8500 but facing issue i.e. if the user doesn't triggers webauth session the login process doesn't flows due to error. The process only flows when captive portal at user end triggers. The whole point of us...
HI all, I need to create a Wlan for guests, so i have a dedicated XDSL line, connected on port 3. i've created an interface with port 3 on physical information, an IP (192.168.10.2) that match with range of my router (192.168.10.1) and setted up DHCP...
Hello all,I have had WiFi network with 8 APs with one SSID which was PSK secured. One month ago, we have added I have created new SSID which is 802.1X secured with ISE but it turned to be nightmare for me. Some part of people are complaining that the...
Hi all,we got a question about our WLC 5508 single controller deployment with 14 access points without a VLAN configuration.When our clients connect to the wifi, we cannot see any ip address of them in the client details page. It shows everytime the ...
Resolved! WLC HA redundancy Query
Hi All, I've 2 WLC's which are configured in HA-SSO mode, During one of the HA testing Scenario, i've removed the cable from the Switch to the primary WLC and Secondary acts as the primary unit and all the operations work normally. but when i plug th...
Hello Everyone,I wasn't able to find anything similar anywhere else for this in the forums. We have a couple deployments of mostly 1832s with some 2802 due to the number of APs on software version 8.5.151.0 that are acting up. Between the two sites...
