Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
WLC is reporting extremely high channel utilisation and interference on 5GHz for one of our older 2602i WAPs. There are no connected clients on the 5GHz radio and there are no interferers being reported by CleanAir. The channel utilisation and interf...
I have a Mac Book Pro in a corporate environment that continues to connect to a AP at 2.4 ghz when there are 5 ghz AP(s) with higher RSSI and are physically closer to the client. An example: Client will (usually) connect to AP "A" at 5 ghz for an 1-...
Dear Experts, Can someone help me understand that when we connect to wireless, a speed value is shown which is probably the data rate at which i have connected. How this value is derived? My value right now is being show 130 Mbps. I can see its poss...
I'm trying to set up a DHCP Pool for a Cisco 1542i AP using the GUI. When I input the following information and press apply it just goes to a white screen and seemingly deletes all the info I just input. When I revisit the DHCP tab it's reset to the ...
HiI have two controllers running code 6.0.182 and one guest controller with same version.I can see the tunnel UP(Both control and data path) in both controller.Guest users are authenticated by web authentication.Suddenly guest users become too slow t...
Dear Cisco communityI have a 2 question about new wireless controller 9800Our partner is about to purchase 3504 WLC to replace 2504. But when entering https://www.cisco.com/c/en/us/products/wireless/3504-wireless-controller/index.html Cisco offers to...
Hi,There's something not really clear for me in the release Note of 8.5.151.0 :From 8.0.x.x => You can upgrade directly to Release 8.5.151.0With a Note : This is applicable only to Cisco 5508 Wireless Controller and Cisco WiSM2. And below there's ano...
Hi Guys,i read a lot of discussions about this issue (same problem a new 2802 doesnt work, but old 2702 works fine). Not sure about country domain (its B now), 2702 has Asee log below: CAPWAP State: Init[*02/19/2020 17:14:28.1597][*02/19/2020 17:14:...
Hello, after WLC 3503 Update to 8.10.112.0 is the Hostname Field Unknow. What is the Issue? In 8.5.140. we´ve got no Problem with that. Can Some one Help?` Thanks a lot.
We are using a Cisco 5520 Wireless Controller with software version 8.3.131.0. But the problem also occured with the former 8.1.102.0 software version. All APs are running in FlexConnect Mode. Moreover we assign an "External WebAuthentication ACL" ...
History:My previous network setup was two Asus APs, one acting as the gateway/router and the other acting as an AP. I have 5 Google Home devices and they were previously connected to the AP closest to each location. I upgraded this network with a C...
I need help configuring my AP for home use... I figured the AP has a lightweight software on it and I have not been able to do anything with it. Please help. I need to use this for home use...
There is no information about the flash size of AP1542 in data sheet or config guides.Does any one know the flash size of AP1542 ? And any document to prove? ThanksHaluk
Resolved! WLC 3504 and NAT Address Setting
I have a WLC 3504, with connecting AP2802 & OEAP1810 access points. The office based AP2802 connect to the WLC fine but the external OEAP1810 will not connect. After doing some research I found that the NAT address had to be set on the WLC management...
I need to up grade my wlc 4404 but cannot find last firmwae. Now i use software version 7.0.116.0please hlep me.Thank you
