I am using aironet 1140's in autonomous configuration to create a wireless bridge for vlan's 1, 5, 10, 15. The problem i am having is the client access point is failing to pass anything but vlan1 through to the client side network. from the client si...
Document states DHCP option 43 helps AP to associate with the WLC in another subnet network. Since APs are configured with static ip address and WLC ip address, why these APs need option 43? In real network, APs also can work well with WLC in differ...
Hello !Regarding the following:NAME: "Chassis 1", DESCR: "Cisco C9800-40-K9 Chassis"PID: C9800-40-K9 , VID: V03 , SN: TTM235208EXNAME: "Chassis 1 Power Supply Module 0", DESCR: "Cisco Catalyst 9800-40 750W AC Power Supply Reverse Air"PID: C9800-AC-75...
I am currently in the process of implementing ISE posture assessment on wireless nets. I am seeing an issue when clients connect and posture status goes from Unknown -> Compliant. The CoA sent from ISE to WLC is failing due to 'NAS Identification M...
Hello,I have a problem when I want to update my AP1832i.In Web, impossible to go through "Cisco.com" and "HTTP" and in TFTP nothing happens.In cli, I have this error: I want to go from 8.5.140.0 to 8.10.151.On my TFTP logs I only have the file "versi...
I have a problem with my Catalyst 9800 L-C.My 9800 had some configurations then i decided erase that config with the command factory-reset allLater my 9800 reboot but when my 9800 started i can see my 9800 in rommon mode. i wastrying initializar wit...
Hye guys, I need an outdoor AP that i can corner mount that will support two differnt directional antenna's. I have a large metal clad building and need to get WIFI on the outside to cover 2 sides of the building like north and east or west and south...
Hi Guy's,We have a Meraki wifi network in our organization and it is already setup and running.Now we would like to use the meraki with Eduroam as well, I found a artikal on how to setup this, but still I have some questions and hope you guy's can he...
Good morning to the crew. I have what may sound like a hair-brained question, but here it goes...Will an MR74 AP transmit a signal without antennas being attached? In other words, will the physical body of the AP itself send out a usable WiFi signal?...
Hello, I have been able to add a MAC address to the disabled client list in my WLC. I was able to do this under Configuration -> Security -> AAA -> Disabled Client. I have tested this and it does provide the desired results however, now I am trying t...
HiI ahve notice that on our coporate WLAN the Interface is Dummy why is this and what is the purpose of the Dummy Interface it has a non routable IP Address and is assigned to a vlan that isnt present anywhere else in the network, there is a interfa...
Hi there, i got a cisco 2504 WLC with OS version - 7.0.112.56. when i tried to upgrade it to new OS , it gives below error. (Cisco Controller) >transfer download start Mode............................................. TFTP Data Type.....................
Hello.It's possible use 2 WLC 5508 en ANCHOR MODE in a Active-Active scenario?.For example, if one WLC get down of service, the other one keep provide service to the anchor clients?.In this moment we have just one WLC 5508 in Anchor Mode. What i need...
Hello Experts, i had converted a 9120 ap into embedded 9800 WLC using https://www.cisco.com/c/en/us/support/docs/wireless/embedded-wireless-controller-on-catalyst-access-points/215303-embedded-wireless-controller-conversion.html but after doing when...
We have 6 WLCs 3 on two of our major locations running 8.3.150 software version. We will be replacing our wireless gear so we will not be updating these WLCs and we are changing vendors. We will not be upgrading the gear until probably at the end of ...
