Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi At AirOS Controller , we can choose multiple Identity Source ( Radius, LDAP,Local) For Client Web-Authenticate: If multiple identity stores are selected, then the controller checks each identity store in the list, in the order specified, from top...
Dear Experts,Can anyone please tell me if Cisco Access points can be installed inside train or Bus? are they vibration certified?Also what other considerations might be put in terms of design like will the APs be able to handle the fast roaming due t...
Have a large Flexconnect deployment. A small number of AP’s per site. Question, can we put AP’s from multiple sites in the same FC Group to save cfg work? The concern is how much data traffic is exchanged for key exchange, mobility roaming, etc. a...
Hello All, I am trying to find a way of configuring the radio settings on a per AP way. What I want to do is set for 2.4 and 5 GHz to be broadcasted only on outdoor APs. Currently, I only have 5GHz broadcasting on my APs at this time. The only way I ...
Hello, Here is a question. Sometimes we assign static ip address to AP, but the AP use dhcp ip address instead of the static ip address? When we check the AP, the static ip address is still there, but But the AP does not use it. Thank you
Hello, Anyone can answer my question? We got wlc and APs. When we try to join APs to wlc, sometimes it failed due to different version. so we upgraded ios for APs then the version of AP is newer than wlc, and AP still cannot join wlc. So we think we ...
So I returned from vacation to an AP on my desk. Apparently, someone tried changing this into a standalone wap for some testing and things turned out very badly. When I putty into it, all I see is scrolling text***Board is not initialized properly*...
I have multiple 1852's getting rejected for VIS.DO.11.4978, 3/0/48 2c:0b:e9:c1:87:80 2c:0b:e9:c0:49:78 x.x.x.xJan 26 04:58:56 kernel: [*01/26/2021 04:58:56.0910] Discovery response from MWAR ''running version 0.0.0.0 is rejected.VIS.DO.11.4978#sh clo...
Upgraded our 5520 controller from 8.5.151 to 8.10.142.0. This was due to needing to support 9130 APs. We replaced the older 3500's and 3600's with 9130's (as 3500 and 3600's were EOL). We have Symbol Workabout Pro4 scanners. They worked fine on...
Hello, We have some AP3802 and WLC3504. After power outage some APs cannot be joining the WLC. Anyone can give some suggestions? Thank you
Since moving to an all Meraki system I have been unable to connect my HP Envy 5530 wireless printer to the wireless. Previous system was an Apple Time Capsule. When switching I did have issues with Wireless sound speakers and smart bulbs. But I have ...
Hello, This is AP, but the AP looks like controller after booting up. Please see the below. What happen? Thanks (Cisco Controller)Cisco Aironet 3800 series Mobility Express
I am upgrading a 5508-50-K9 from 7.6.120.0 to 8.2.170.0 as an interim to an eventual 8.5.171.0 The upgrade was successful and all APs downloaded the new image as well. Prior to the upgrade the base permanent license on the controller is 50 APs. ...
Hi, does anyone know of a way to remotely check statuses of signal strength on an IR809G Cellular Router? Thanks
Hello, There are two interfaces in WLC. One is static management interface vlan 10 and second is created vlan 20. Trunk connections are at between WLC and SW1, and between SW1 and SW3, The port F0/1 is access mode. If F0/1 is assigned with vlan20, wh...
