Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Issues moving AP onto new vWLC
Hi,We are having to migrate all our APs from one vWLC to another vWLC (due to various issues including migrating from VMWare to Hyper-V). I'm using 1 AP as a test before moving the rest.I've had various issues in doing this, so will describe where I...
Hello guys. I need your help. I have the following machines: WLC 8.2.166.0 vMSE 8.0.150.0 CPI 3.1.0 I can see reachable the MSE from CPI, but the NMSP status is inactive. all machines has the same time zone and clock. Thank you for your help
I recently installed vWLC release 8.5 in Hyper-V and referenced the hyper-v deployment guide. Once installed and configured, I could ping the management interface IP from the hyper-v host but couldn't load the web GUI from a browser on the host. Afte...
WLC C9800-40-K9 on 16.12.1 We are seeing a lot of alarms in ISE for "12929 NAS sends RADIUS accounting update messages too frequently". The NAS is a 9800 WLC and the clients are mainly phones on our eduroam SSID. On the old 5508 controller there is n...
Hi, I have a Cisco 5508 WLC (8.3.150 release) with 25 WLAN SSID configured and 352 Acess Point. In particular there is a WLAN SSID configured as Layer 2 Security as 802.1x (WEP). These 352 Access Point are installed in more location and each locatio...
Hello Cisco members, I would like to ask if obtaining RSSI data from WLC controllers is possible, for associated and/or unassociated clients? I read some resources on the Internet which says it's doable via "Cisco Wireless Location Appliance", but in...
Hi, We have a 2504 with HA sku and doesn't have a purpose for it and now we're thinking of re-purposing it. My question is, is it possible to install an AP adder license to a 2504-HA and will the HA in the sku go away after? Thanks in advance.
I'm currently working on a small POC to install OEAPs so our call center employees can work from home (ideally to bring a phone home with them and connect it to the OEAP POE port). We have softphones too but apparently management is still asking to m...
How can we make a C9300 switch act as a stand-alone for the 9800 WLC . In the documentation it says we can't act as stand-alone - is there a work-around / alternative?
My Customer use Cisco Prime Ver 1.4 U2it Background Task in Configuration backup is show failure all Device but I can Audit or syn config from WLC is success but config backup not success i need workaround prove issue ? Thank
I have a single 3802i with CME 8.5.151. The wireless clients can ping their default gateway and any other wireless host. These same wireless clients cannot ping any non-wireless (aka wired) host on the same subnet. I've been looking through the co...
Resolved! WiFi design best practices
Was wondering if someone could give a second set of eyes on some WiFi Design. I’m at a location with multiple different switch stacks, each stack has a L3 IP scheme for ethernet, and a separate L3 IP Scheme for WiFi. I wasn’t around during initial i...
Rogue auto-containment may have legal consequences, so it should be clear whether or not you are enabling it.I think Mobility Express is not clear about auto-containment. I just found the "Rogue Policies" option in the Best Practices menu. This optio...
Hello.I have this issue. I connected many AIR-AP1852I-E-K9 and AIR-AP1852E-E-K9 (they need 20.9W) to different switches that provide 15.4W so I saw "PoE/Medium Power (15.4 W)" on WLC. To provide what my APs need I used a power injector but even after...
