Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
We have clients that roam from building to building on our campus, and these clients maintain their same IP address with Mobile-IP. In certain situations however, the client will no longer have its traffic tunneled, and it will come over the subnet o...
i have 5520 cisco WIFI controller and the model of AP is AP1810W , it is working fine but if any access point goes down for any reason i can't see any alarm or log on the controller to identify which AP is down just i can know that the number of regi...
Hi to all, I recently puchase a new AP, model is AIR-AP1562E-E-K9.I think that it is a lightweight firmware, i see SwVer 8.3.111.0. cisco AIR-AP1562E-E-K9 ARMv7 Processor rev 1 (v7l) with 1030528/670976K bytes of memory. Processor board ID FCZ21XXXXX...
I have a Cisco WLC 2504 with the default QoS profiles defined (Wireless Section > QoS > Profiles). I have a WLAN tied to the Bronze (background) QoS profile. When I did a SPAN and Wireshark on my Cisco switch, I expected to see frames with the 802.1p...
Can you please advise which cisco solution for wifi is better for bigger office.I am looking to implement on two floors.ThanksSent from Cisco Technical Support iPhone App
I borrowed a 'Cisco SG300-10 10 port gigabit managed switch' from work to practice things i'm learning from my CCNA course. I have tried a serial to ethernet cable for console connection, and a regular ethernet cable from one of the ports. I have tri...
Hi, I am using Cisco packet tracer v 7.2.0.0226. I am using following topology. |LAP|------------(ethernet)--------------|3560 multilayer switch|-----------------(ethernet)---------------|WLC| As a start, I configured management IP address on WLC, c...
Cat3560CX >>>>>> WLC2504 >>>>>> AP3602i gi0/x Trunk LAN1 LAN4 PoE LAN I have a VLANx (10.x.x.0/24) for infrastructure configured on the Cat3560.I have an AD server configured wit...
Every device are connect to SSID but one device not connect. 802.1X in use this SSID. Debug logs are here: *IPv6_Msg_Task: Sep 02 06:09:27.837: b4:9c:df:4b:f0:f7 Link Local address fe80::467:6bd4:8946:e838 updated to mscb. Not Advancing pem state.Cur...
Resolved! Wireless
I have an AP that failed. I need to replace it. However I cannot find that AP in the any of my the controllers. I see the AP list on the controllers' web GUI. However the MAC for this AP is not on the list. How do I identify what the previous configu...
I have an 1832i AP at a remote site with IP address in the 192.168.13.0/24 range. It was set up originally as ME and I tried to change it to CAPWAP, but that failed and the AP's on site are now not broadcasting SSID's. I have been trying to force it ...
Hi,I would like to upgrade WLC 2504 from 8.2.151.0 to newe image. So I follow release note: If you are using Release 8.2.15x or earlier, we recommend that you upgrade to Release 8.2.16x or 8.3.x and then upgrade to Release 8.5.140.0. so I upgrade to...
I have to upgrade a 5520 WLC from 8.2.x to 8.5.x. The CIMC module is not used or connected so no remote CIMC access. As usual the release notes are not very clear but quotes bug reference CSCvo33873 that states for 5520 and 8540 appliances "We recomm...
I've tried everything but I can get the CAP to keep a static ip address. I've entered it the WLC GUI from the panel shown below, bottom right, from the WLC CLI [(Cisco Controller) >config ap static-IP enable AP1 192.168.170.100 255.255.255.0 192.168...
Hi,we have a IR829 with an integrated AP803. The router works fine but when we reverse telnet in the router to gain access to the console of the AP, we see that the AP803 is stuck in ROMMON.When we do boot, the AP tries to boot its firmware but after...
