Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Can you configure a RF Profile to disable 2.4 GHZ only on a 8540 WLC version 8.10.121.0? I have configured a global setting to lower the 2.4 GHz radio to 5 but I'm finding that some area's I would like to disable the 2.4 GHz per radio AP group. Thank...
Resolved! DTLS license for Catalyst 9800
Hello,Could you advise how to order DTLS license(LIC-C9800-DTLS-K9) for existing Cat 9800 controller ? For example, I have installed C9800-L-C-K9. It was ordered without LIC-C9800-DTLS-K9 license.Now I need to enable DTLS encryption. So how to order...
Hi All, In one of the floors of the building I am facing strange issue. The room is square, not big, holding 12-16 people. There is one AP in the middle of room with only 5ghz enable and no other signals in the same channel is visible all clear. Ther...
Resolved! Licence AIR-CT2504-K9 broken down
Hello, I have a AIR-CT2504-K9 buy without licence, licence was bought alone.The CT2504 is broken down. If I bought a AIR-CT2504-K9 refurb, can I keep my old licence ? Thank you
We have Cisco 2504 - 2 Nos. Each box has 10 AP licenses.I would like to make them as HA setup. I will need to use 15 APs at a time. So can I move the licenses from WLC2 to WLC1 (so that WLC1 will have now 20 licenses), WLC2 will have no license but j...
Hi Experts,im having issue adding MSE to prime with below error:No response from server. it may be unreachable, or server is down or https connection to server failed. but the mse was already added before. mse is version 8 and prime is 3.6. saw thi...
I have a rectangular auditorium with 2 APs diagonally and 1 AP outside as a backup. The 2 APs inside are identical C9120AXE. But sometimes I have a very uneven client distribution. For example, 50 clients on the AP1 5GHz band and 1 on AP2. Now:- AP1 ...
Hello,We are implementing SD-Access network managed by DNA Center. Wireless network is also fabric.Currently for people on their desk, there is not much problem but there is one important complain from upper management about his Whatsapp/Telegram/Zoo...
We have 37 APs. AP models are all 3802. Only 23 devices can be seen under 802.11b/g/n, as shown in the figure below. You can see 51 devices under 802.11a/n/ac. Some customers told us that their devices that can only use 2.4Ghz cannot connect to wifi....
Hi Everybody, We haved changed of Service Provider in a branch. This little branch has a Cisco AP 2800 in Flexconnect mode, after migration, the AP doesn't connect anymore. The AP is reacheble from ping, trace, SSH, however, DTLS tunnel go to TEARDOW...
Hi, We are using 200+ APs in the plant office and they are connected to WLC.Sometimes switches shut down for some reasons, then related APs were shut down too. The problem is when the all devices are rebooted after shut down, AP's IP changed even APs...
Hello , I Can't login Office Extended after loading mobility express into 2800E , i want to use my access point as a standalone , i can login to WLC on the same AP with success , but i cant reach the Office Extended in order to configure it as a stan...
hello, by default, unacknowledged probe requests are filtered on wireless access points. if the filter is turned off...is it possible to make them visible anyhow? br +t hx
ＷＬＣによるＡＰの再起動https://community.cisco.com/t5/%E3%83%AF%E3%82%A4%E3%83%A4%E3%83%AC%E3%82%B9-%E3%83%89%E3%82%AD%E3%83%A5%E3%83%A1%E3%83%B3%E3%83%88/wlc-%E3%81%AB%E5%B8%B0%E5%B1%9E%E3%81%97%E3%81%A6%E3%81%84%E3%82%8Bap-%E3%81%AE%E5%86%8D%E8%B5%B7%E5%8B%95...
Dear all, Please help and comment on my post. Below is the topology. SSID A, Cisco WLC and Apply are in 192.168.1.0/24 subnet.SSID B is Vlan 2 and in 192.168.2.0/24 subnet.No any acl is on the Router or switch. After an iPhone connect to SSID A, Ai...
