Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello Everyone, I'm facing client disconnection , it tries to connect to the AP and the user is steady and not moving. Captured RA traces and found out the it is happening due to PMKID is sent during authentication.Client sending authentication reque...
5520コントローラ（冗長）からCW9800M（冗長）への更改につきまして、 検証が必要と思いますが、入替の考え方として、5520のコンフィグに設定を似せておいて、 5520の幹線を起動後のCW9800Mに差し替えたら、自動的に従属APはCW9800Mに向いてくれるのでしょうか？ これができない場合は、CW9800MのIPアドレスを5520と別のものに設定して、従属APに個々にSSHでアクセスして CW9800MへIPアドレスを変更してAPを再起動させ、徐々にCW9800Mに向けさせる。 考え方...
Has anyone been hitting this bug lately? In particularly when running 17.x.x code. We are encountering an intermittent issue when upgrading code on our 9800 series WLCs, upon boot with new code all AAA/RADIUS authentication is broken. Only PSK WLANs ...
Hello All,I am a new NOC tech, and my enterprise APs run on Catalyst. Does anyone have any learning resources for maximizing Catalyst functions for troubleshooting wireless outages? Most of the learning material I've been able to find is focused on d...
Hi AllWe are having some issues with some MR42s, basically we have a Guest network and its using the AP in NAT mode, we can ping devices on our LAN for some reason, even though there is a deny rule on the SSID blocking them to reach local networks, w...
Hi everyone,I need to know if it’s possible to configure the Cisco 5508 Wireless Controller to use LAG mode with LACP.The controller is running version 8.0.133.0.I’m migrating this controller to new Cisco Meraki 9300M switches managed through the Mer...
Anyone know how much mac address can be added to the local mac filter for WLC2504 series?
I successfully converted my 3802i ap from lightweight to ME But i cant access it via web interface and it has these warnings below when i put the user and passwordUser: EBENEZERPassword:*********Warning: Missing TFTP/CCO params, Please Configure the ...
I have several networks setup as Meraki AP assigned (NAT mode). I absolutely love this feature. It lets me quickly deploy an Internet only network and everything is self contained in Meraki. I typically use this for visiting groups coming to our camp...
We have two Cisco Catalyst 9800-L-F WLC's in HA config.We setup a Guest wireless SSID with a custom WebConsent page.Currently when a use accesses the SSID it takes them to a "Your connection is not private" HTTPS page.We don't need HTTPS on our Gues...
We enabled Meraki Cloud Monitoring on our Catalyst 9800 WLC (IOS XE 17.15.3.28) and it shows up in the Meraki Dashboard.However, all connected IW9167EH-A APs fail to register. Output of show ap meraki monitoring summary shows either:Not Registered, o...
Hello, everyone. I've read that mobility tunnels use UDP port 16666 for control traffic and EoIP for data traffic. I've also read that if encrypted mobility is used, UDP 16667 is used for data traffic. I've also read somewhere that 16666 and 16667 ar...
Hi,allHow I control the Bonjour forward from specified source vlan to destination vlanMy scene has total 3 floors, two SSIDs and per vlan/subnet per floor for each SSID, detail as below.SSID-A1F:vlan 101 with bonjour-serivice-1F2F:vlan 102 with bonjo...
How to move AP from secondary WLC to primary WLC in N+1 in wlc 9800
We are trying to see if Meraki AP has two partitions for firmware images. Two partitions help in surviving a failed upgrade.Do Meraki APs have two partitions, one to store the current image as the backup & the other to store the new one being upgrade...
