Hi, I have ME running 8.5.131.0 and have some questions about Radius authentication server config. I have two external radius servers configured and being used by the production WLANs. I need to test a new radius server and plan to create a new test ...
Hi All, I wanted to check how other do this in their networks. We are setting up a new wireless network and need to authenticated the APs as they are connected to the network using EAP-FAST. The network has been configured in closed mode using ISE. T...
Hello,we have installed many Cisco APs? In dem floor map I can see that many APs send with low transmit power. The users complain about low signal strenght. Where can I see the transmit power on the WLC gui and how can I change the transmit power onl...
Hello Dear community, I am having the following error messages in the console of the AP 3500: *Jan 1 01:41:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.50.10 peer_port: 5246*Jan 1 01:41:18.207: %DTLS-5-ALERT: Receive...
While reading the documentation for using 802.11k, am i correct in assuming that this function will not work if the clients are not CCX compatible? Most of the clients are iOS devices and are showing on the controller "Home Page" as being CCXv0. Than...
This also includes a Cisco AIR-LAP1252AG-A-K9. These APs lose POE when switches in the building are rebooted due to power outages. When the switches are back online and booted up, the APs are still powered off. In order to get the APs back online...
On the backend, I had Meraki support disable 802.11ax capabilities on all AP's since it was causing an issue and we didn't anticipate utilizing it yet fully.I do have L3 roaming configured. It is the worst thing ever and Meraki support has confirmed ...
I have inherited a 2504 WLC (still running7.0.220.0) which has one corporate SSID defined.I intend to create a new SSID and interface for a guest network, which will be on a separate subnet and VLAN. The VLAN is yet to be defined.I am running into tr...
Hi,I would like to know what is the added value for the wireless health and safety site survey? Knowing that an AP cannot exceedthe maximum TX power for specific country.Could you please point me to the right document? I was not able to get clear vie...
A customer is performing the ipv6 implementation. the wlc is currently being configured, the ipv6 address was set in the management interface, this ip responds ping from the core, but from another vlan in the network does not respond ping. I would li...
Hi all.I am using WLC 3504 and AP air-ap3802I-F-K9 with firmware 8.5.151.0 configured as flexconnect AP. We have 3 SSIDs, 2 of them are using dot1x and the rest is PSK.Once a day, there is a random client (not happen to all client) having difficultie...
Hi, We are looking to buy a Cisco Aironet router in India and we found that part number for that is AIR-AP2802I-D-K9I.While our Singapore team has already a same router with part number:AIR-AP2802I-S-K9. Is there any difference in terms of technical ...
Ive set up a wireless network today consisting of Cisco 2800 WAP's and a 2504 WLC. For some reason the AP's will not join the controller. I have a consoled into the wlc and this is the output *spamApTask4: Jan 01 16:30:15.600: a0:23:9f:21:83:40 Deco...
One of our networks (which is set up the same as all of our other networks) received a notification that "The Cisco Meraki Cloud is having difficulties communicating with this device." This message is showing up on all of the APs on this one network....
The company I work for just purchased one of these APs and I am having a hard time configuring it. I hae done several searches and I can't find what i'm looking for. It seems that after a factory reset by holding down mode during power on, that I can...
