Hello I would appreciate if you could help me with IOS XR SNMP. I use the Snmpwalk command to find the state OID for BGP sessions. When I run the command the session by in time-out? I use IOS XR version 5.3.4 snmpwalk -v 2c -c toto X.X.X.X or snm...
Hello, do you have experience with building GISO for NCS540 (XR7 platform)? I have tried gisobuild.py (version 0.38), but the script return errors. Thanks, Peter
Hello, We have a line card A9K-MOD400-TR which was inserted in a chassis 9910 and worked in version 7.1.3 (64bit) , we want to remove this card to another chassis with RSP880 in 32 bit version 6.1.4 . Due to some other second generation card in the s...
Hello.I have a setup like this:Where both sites are connected trough a bridge.The issue here is that the bundle is not load-balancing, the traffic is flowing only through one of the linksThe customer runs mpls between this two sites and on top pppoe....
Hello Community! I upgraded our NCS57C3 routers from 7.5.2 to 7.7.21 but after this the MPLS traffic is not load balanced between the links. NCS57C3 with 7.5.2 load balances the traffic perfectly but 7.7.21 - first link is exceeded, second and third ...
In IOS XR, every 20th commit XER is doing config rebase operation and it delays the commit. And if we terminate the ssh session while rebase operation is on-going, then the config which we commit will rollback.Is there a command (exec or bash) to for...
Hello all,we are planning an upgrade of our ASR9910 to new 64bit system. IN release notes there is a mention of bridge SMU CSCvw57276 required for this upgrade path. But there is a note that it is applicable for 64-bit systems.he following table outl...
Hi all, We are monitoring the ISIS Adjacency status on an ASR9k using SNMP. The issue appears when pooling the isisISAdjState for some of the entries in the table. For example, if we walk the table we see all the adjacencies and there corresponding i...
Hi Guys, I'd like to import specific prefix from VRF B (RT:65500:1000) to VRF TEST. I have the following config but it's not importing the specific prefix. If I configured import route-target 65500:1000 then I'll be receiving all the prefixes in that...
We have an ASR-9001 and it was running 5.1 and we attempted to turboboot unit to 6.4.1. Then this happened. RP/0/RSP0/CPU0:Apr 19 08:04:04.410 : cfgmgr-rp[158]: %MGBL-CONFIG-0-INIT_FAILURE : Configuration Manager was unable to initialize the Admin Co...
Hi,I regularly use bridge domains to connect sub interfaces on different vlans using this sort of configuration:interface GigabitEthernet0/0/0/5.21 l2transport description CUSTOMER A WAN encapsulation dot1q 21 rewrite ingress tag pop 1 symmetricinter...
RFC 2544 tests fail on all frame sizes below 9000 bytes. The results are also worse the smaller the frame size. I have tried adding a policy-map on the egress interface per the post below with no succes:https://community.cisco.com/t5/xr-os-and-platfo...
Hi, all: Just curious if on an XR box is possible to bundle a 10G and a 100G interface together. Will XR support it? Is there a way to have, say a 100G uplink, and if growth is needed use 10G interfaces (several)? I'm thinking I could do this by usin...
We are in progress of upgrading from ASR1004s (XE 3.16.08) to ASR9901 BNGs (7.5.2). In doing so, we no longer have the ability to show connected PPPoE sessions using a simple "telnet {ROUTER} finger". We have a Unix server that would issue the comm...
I am trying to change interface IP address using ncclient via netconf and the config which I am trying to do is as below.Please help here to get the IP changed using ncclient for the interfaces in IOS XRv9k """<config> <interface-configurations xm...
