HI I have a VSM on the ASR9K, and i use the NAT44 on the VSM and i need to install a good syslog server to save NAT session records for 3 month period and be able to easily search in the records for specific IP any suggestion what is the best ...
Forum Posts
Hi these.I configurated tunnel IPv6 over IPv4. Althought interface tunnel is up.But on SW_AGG_01, only ping successful: 1001:1:1::1, not ping 1001:1:1::2.The same on SW_AGG_02, only ping successful: 1001:1:1::2, not ping 1001:1:1::1.I don't know caus...
I have read through the excellent post on TCP MSS Adjust on ASR9000 by Aleksandar Vidakovic. According to that post, to adjust MSS one must configure the hw-module location 0/0/CPU0 tcp-mss-adjust np 1 value <number> and then apply it on the correspo...
HI I have a VSM on the ASR9K, and i use the NAT44 on the VSM i need to get the syslog of the NAT entriesbut when i use the syslogexternal-logging syslogsserveraddress 20.1.1.2 it only get the source address and Global address ,but it not have desti...
This is a place holder for questions on FN 63979Details are here: http://www.cisco.com/c/en/us/support/docs/field-notices/639/fn63979.htmlUse this thread to ask any questions.
I am trying to modify the outbound policy for an existing BGP peer on ASR9000, I shut down the BGP session, entered the address family for specific neighbor and removed the existing route-policy, then i applied the new route-policy for outbound traff...
Resolved! CEF unresolved
Hi All, I have created a BGP-LU inter-domain within the same AS on my lab. The topology is: CE1 |----------------| PE1 |----------------| P1 |----------------| ABR1 |----------------| ABR2 |----------------| P2 |----------------| PE2 |-------------...
Resolved! BFD between ASR9001 and Palo Alto
Hi everybody, hope you are fine. I'm trying to implement BFD between two ASR9001 routers and a Palo Alto PA-5250 Firewall. I've configured BFD on the routers (under OSPF process)and the Firewall but they are not seeing each other, BFD sessions are no...
If you modify a BGP neighbor-group that is apllied to established BGP neighbors, does that reset the neighbors that are using the group?
Is there a way when using netconf-yang and ncclient to get a diff of changes from edit_config before commit() is called? From CLI i'd want something like the output from 'show commit changes diff' but not seeing any ways to do this from ncclient.
Hello my chassis have a error logging about L3 CACHE ERROR，is my hardware wrong and need RMA？ LC/0/2/CPU0:Apr 22 06:49:32.597 : p40x0mc[75]: ====== L3 CACHE ERROR #1 ====== LC/0/2/CPU0:Apr 22 06:49:32.648 : p40x0mc[75]: CPC Registers: OFF ...
Hello, Could you please let me know if it possible to install 2 x A9K-MPA-4X10GE on ASR9001S ? The A9K-9001-120G-LIC is already installed. The running software is 4.3.2 Thanks
Hi, I would like to confirm the below tagging? Im bit confuse 1. In this scenario all vlans coming from Customer A will have a new tag of 100 (S-TAG) and once the frame reaches the other end/PE02 swtch will strip off the additional outer vlan. ...
I configured following setup: PE: I match outer tag and POP it, then Xconnect to BNG. BNG: PWHE is used for termination, at present no BNG dynamic profile is uses, just a simple subif. Issue is, PWHE is up, but not sending any traffic, only receivi...
RP/0/RSP1/CPU0:ios#dir usb:Sun Dec 7 19:18:12.309 UTCDirectory of usb:131136 -rw- 2281144320 Mon Dec 8 09:08:46 2014 ark9k-px-k9.tar69618 drwx 32768 Sun Dec 7 19:07:07 2014 LOST.DIR8006893568 bytes total (5725683712 bytes fre...
