Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1999344members
1359741discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Route redistribution

Hi,I would like to redistribute BGP and EIGRP mutually:R1 - R2 EIGRP AS 100R2 - R3 BGP AS 100R2:Router EIGRP 100default-metric 1000000 1 255 1 1500Network 10.12.1.0 0.0.0.255redistribute bgp 100 metric 1000000 1 255 1 1500!Router BGP 100BGP Router ID...

Resolved! Split Traffic between 2 Firewall from my Core Switch C3850

The goal i want to achieve here based on from the diagram below:i want user1 - 192.168.20.x to pass FG-FW01 192.168.1.1i want user 2 -192.168.50.x to pass FG-FW02 192.168.1.111currently the routing is going to FG-FW01 with static ip route 0.0.0.0 0.0...

HeraldSison_0-1729088974829.png

Fabric graphical view

Hi all,I wonder me why I see the device in attached draw without link to c9300 device (blue, in edge role).Does anyone know why it is not graphical linked to c9300?It is the device in the above left corner (white without link). It has the same config...

p11l by • Level 1
  • 120 Views
  • 4 replies
  • 0 Helpful votes

Antenna parameters and gain in EWC

Some doubts about antenna gain and parameters in EWC. I can't understand why is so complicated: I have to check which antennas the AP are using (A, B, C, D) and the antenna gain in 0.5 dBi units. Cases:1. I connect an AP C9115AXE with 4 antennas ANT2...

jmprats by • Level 4
  • 61 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Error in DNAC-Template CLI + Velocity

Hello Community, i am pretty new to this. i try to update the certificate of an Trustpoint via CLI-Template ( Velocity ) for an C9300l-SwitchEverything i try gives me an error.Here is what im trying to do:#MODE_ENABLE##!INTERACTIVEcrypto pki authenti...

Connecting two CBS350 Switches

I've two CBS350 series of switches that I wish to setup for connecting IP Cameras and accessing them from the Control Room.IP Cameras will be connected to CBS350-8S-E-2G.CBS350-8S-E-2G will be connected to CBS350-24T-4X over Single mode fiber via a p...

No Auto Summary Not Saved in 3650_24PS

Hi,In Packet Tracer, I’m using a Layer 3 switch (3650_24PS) with OSPF configured. When I enter the command no auto-summary and save the configuration using either write memory or copy running-config startup-config, the setting is lost after a restart...

drushka by • Level 1
  • 35 Views
  • 1 replies
  • 0 Helpful votes

Duo Deployment to protect Gsuite emails

Hello everyone,I was looking for information on how to deploy Duo for a customer using G Suite emails. This customer doesn't have a Windows server or any other authentication source. Is it possible to deploy the Duo MFA solution?Thanks!

jcuni by • Level 1
  • 42 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Cisco 2960-S MBIST failed

Hello there,we've recently been resetting some of our Cisco 2960-S series switches, and we are getting some weird post messages.When we boot into ROMMON and factory reset them, after the boot command when the firmware boots, we get 9 MBIST fails, but...

Load more