Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1990039members
1346953discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Resolved! PDMT cannot migrate WLC

Hi, Wondering if anyone has run into the following issue. Trying to migrate Prime to DNA center using the inbuilt PDMT but everything works except the WLCs will not migrate to DNAC. I've turned off SNMP v1 and v3 on the WLCs to no avail. One thing to...

elemzy01 by • Level 1
  • 557 Views
  • 3 replies
  • 0 Helpful votes

Firepower 7.42 issue interface Management0 has no link

I'm in the process of upgrading all of my firepower devices from 7.2.8 to 7.4.2 as it is the suggested release. we use the data interfaces as the management interface for most remote devices. As I upgrade each one, I'm now presented with a critical w...

Lee Dress by • Level 1
  • 83 Views
  • 4 replies
  • 0 Helpful votes

Firepower 1010 readiness check stuck at "Please Wait"

I have a Firepower 1010, on 7.0.0-94 that I'm trying to upgrade to 7.4.2-172. I ran the readiness check last night at 8pm.   12 hours later, at 8 am, it still says "Please wait" on the readiness check, and won't let me hit the upgrade button. Followi...

FTD Migraton Uisng FMC

HiI dont have access to a  lab so am asking a couple of questions'I want to migrate from one FTD to an HA pair, On the FMC thats is currently managing the single FTD there is a sub doamin for the FTD but on the new FMC where I want to migrate the FTD...

TCP optimization

Hello experts, We have a user with some performance issues, and he believes there is something related with TCP optimization enabled on Nexus switch that is degrading the performance due to some previous experience. Just want to confirm if Nexus has ...

noc tesys by • Level 1
  • 151 Views
  • 3 replies
  • 1 Helpful votes

Flex Config help

While trying to insert WCCP into the FTD, the configuration was wrong, TAC gave me the wrong type of ACL which broke the configuration of our running FTD. I have very limited knowledge of what or how flex config is. I need to remove the wccp part of ...

Resolved! Dialer Interface Question

HiHow do I check that all is ok with a Dialer Interface which is using Chap for authentication, is there any basic commands I can run to check all is ok, also I notice that the Dialer Interface dosent get an IP Address and never has but it does get a...

Especific voip model with wrong time

Hello, on my CUCM I have different models of voip phones (8865, 8811, 7821, 6921 and 3905). We recently detected that only the 3905 model displays a different time on its screen compared to the other models. The time displayed is one hour less than t...

does IOS XE 17.12.3a support ISAKMP group 5 ?

I have a C8500-20X6C running version 17.12.3a and I want to config a IPSec tunnel with ISAKMP group 5, but looks like it is only supporting the bellow DF groups: Router(config-isakmp)#group ?14 Diffie-Hellman group 14 (2048 bit)15 Diffie-Hellman grou...

Difference between ip vrf "word" and vrf defination "word"

I have an Analog Voice Gateway that I need to creare a vrf and this VG accepts these commands  ip vrf "word" and vrf definition "word" and I really don't know the differences beyond that the first one is for IPv4 and the second one accept IPv4 and IP...

Load more